Rockwell Automation Allen-Bradley PowerFlex 755T Series, Programming Manual, Page: 89 / 130

Share

Page: 89 / 130

Rockwell Automation Allen-Bradley PowerFlex 755T Series Programming Manual Download Page 89

Rockwell Automation Publication 750-PM101B-EN-P - April 2022

89

Chapter 4 Troubleshooting

HIM Indication (Fault

Display Screen)

The popup fault display screen automatically appears when the drive detects a
fault condition for the host drive or any connected peripheral. By default, the
status bar flashes to alert the operator. To change the display flash mode, see
the PowerFlex 20-HIM-A6 and 20-HIM-C6S HIM User Manual, publication

, for instructions.

The fault display screen displays the following information.

•

Fault Code number (See

Fault and Alarm Display Codes on page 102

•

Fault description

•

Elapsed time (in hh:mm:ss format) from fault detection

Figure 66 - Pop-Up/Flashing Fault Display Screen

Manually Clearing Faults

Soft Key Functions

Label

Name

Description

ESC

Escape

Reverts back to the previous screen without clearing the fault.

CLR

Clear

Removes the pop-up Fault Display screen from the display and clears the fault.

Single Function Key

Key

Name

Description

Stop

Removes the pop-up Fault Display screen from the display and clears the fault.

Stopped

0.00 Hz

AUTO

Fault Code 81

Port 1 DPI Loss

Elapsed Time 01:26:37

ESC

F

CLR

– – FAULTED – –

Step

Key(s)

1. Press the ‘Clear’ soft key to acknowledge the fault. The fault information is removed so that you

can use the HIM.

2. Address the condition that caused the fault.

The cause must be corrected before the fault can be cleared.

3. After corrective action has been taken, clear the fault by one of these methods:

Press Stop (if running the drive will stop)
Cycle drive power
Select the ‘Clear’ soft key on the HIM Diagnostic folder Faults menu.

CLR

«
...
87
88
89
90
91
...
»

Summary of Contents for Allen-Bradley PowerFlex 755T Series



































































































































Reviews:

No comments