Rockwell Automation Allen-Bradley PowerFlex 755T Series, Programming Manual, Page: 102 / 130

Share

Page: 102 / 130

Rockwell Automation Allen-Bradley PowerFlex 755T Series Programming Manual Download Page 102

102

Rockwell Automation Publication 750-PM101B-EN-P - April 2022

Chapter 4 Troubleshooting

Hardware Service Manual

The PowerFlex 750-Series AC Drive Hardware Service Manual, publication

, provides schematics and detailed instructions on part replacement

for PowerFlex 755T products.

The PowerFlex 755TS Products with TotalFORCE Control Hardware Service
Manual, publication

, provides schematics and detailed instructions

on part replacement for PowerFlex 755TS products.

Fault and Alarm Display

Codes

Event numbers for PowerFlex 750-Series faults and alarms are displayed in one
of three formats.

•

Port 00 (Host Drive) displays the event number only. For example, code
21 ‘Clr Fault Queue’ is displayed as:

Fault Code 21

.

•

Ports 01 through 09 use the format PEEE, indicating port number (P) and
event number (EEE). For example, code 1 ‘Analog In Loss’ on an I/O
module installed in Port 4 is displayed as:

Fault Code 4001

.

•

Ports 10 through 14 use the format PPEEE, indicating port number (PP)
and event number (EEE). For example, code 37 ‘S OverTemp Alm’ on Port
14 is displayed as:

Fault Code 14037

.

Common Symptoms and

Corrective Actions

Fan Type

Frame 8 Common Bus Inverters

Frame 9 Common Bus Inverters

Frame 10…15 Common Bus Inverters

IP21, NEMA/UL Type 1 IP54, NEMA/UL Type 12 IP21, NEMA/UL Type 1 IP54, NEMA/UL Type 12 IP21, NEMA/UL Type 1 IP54, NEMA/UL Type 12

Control Pod Fan

Dual

Dual

Dual

Dual

Dual

Dual

Stirring Fan

None

None

None

None

None

None

Heatsink Fan

Present

Present

Present

Present

Present

Present

Input Bay Fan

None

None

None

None

None

None

Power Bay Roof Fan

None

Present

None

Present

None

Present

Wire Bay Fan

Present (with option)

Present (with option)

Present (with option)

Present (with option)

Present (with option)

Present (with option)

Control Bay Fan

Present (with option)

Present (with option)

Present (with option)

Present (with option)

Present (with option)

Present (with option)

Drive does not start from Start or Run inputs that are wired to the terminal block.

Cause(s)

Indication

Corrective Action

Drive is faulted

Flashing red status light

Clear fault.

• Press Stop

• Cycle power

• ‘Clear Faults’ on the HIM Diagnostic

menu

Incorrect input wiring. See Installation

Instructions, publication

, for wiring

examples.

• 2-wire control requires Run, Run Forward,

Run Reverse, or Jog input

• 3-wire control requires Start and Stop

inputs

• Verify 24 Volt Common is connected to

Digital Input Common

None

Wire inputs correctly.

«
...
100
101
102
103
104
...
»

Summary of Contents for Allen-Bradley PowerFlex 755T Series



































































































































Reviews:

No comments