Rockwell Automation Allen-Bradley AADvance T9110 Solutions Handbook Download Page 72 | Manualshive

Page: 72 / 165

background image

72

Rockwell Automation Publication ICSTT-RM447M-EN-P - July 2019

Chapter 4

AADvance System Architectures

Certified Configurations

Revisions of modules are subject to change. A list of the released versions can
be obtained from Rockwell Automation.

Table 12 - Central Modules

Table 13 - Input Modules

Modules

Certified
Configuration

Conditions

Processor Module

T9110

1oo2D, 2oo3D

Safety-related and can be used for safety-critical
applications in SIL 2 with 2 modules fitted and SIL 3
applications with 2 or 3 modules fitted.

Note

: For both Low and High Demand applications

you must use a minimum of two processors.

Modules

Certified Configuration

Conditions

Digital Inputs

T9401/2, 24 Vdc, 8/16 Channel,
isolated.
+
T9801/2/3 Digital Input TA, 16
channel, Simplex/Dual/TMR

1oo1D, 1oo2D, 2oo3D

De-energized to action (normally
energized): SIL 3 with 1, 2 or 3 modules
fitted.
Energize to action (normally de-
energized): with 1, 2 or 3 modules fitted

Note

: When the integrity level is at 1oo1D

then the faulty module must be replaced
to restore the integrity level back to 1oo2D.

Analogue Inputs

T9431/2, 8/16 Channel, isolated
+
T9831/2/3 Analogue Input TA, 16
Channel, Simplex/Dual/TMR

1oo1D, 1oo2D, 2oo3D

Within the manufactures specified safety
accuracy limits of 1 %. The safety state of
the analogue input has to be set to a safe
value which is a calculated value based on
a count value of 0 mA. (refer to the
AADvance Configuration Guide Doc Nos:
ICSTT-RM405 and ICSTT-RM458 for more
details)
SIL 3 with 1, 2 or 3 modules fitted.

Note:

When the integrity level is at 1oo1D

then the faulty module must be replaced
within the MTTR assumed for the PFD
calculations to restore the integrity level
back to 1oo2D.

«
...
70
71
72
73
74
...
»

Summary of Contents for Allen-Bradley AADvance T9110






































































































































































Reviews:

No comments

Related manuals for Allen-Bradley AADvance T9110

Brand: Paratec Pages: 8

Brand: J+J Pages: 33

Brand: Hach Pages: 2

Brand: Hach Pages: 12

Brand: Hach Pages: 472

Brand: Hach Pages: 64

Brand: V2 ELETTRONICA Pages: 6

Brand: Hach Pages: 210

Brand: Hach Pages: 36

Brand: Hach Pages: 72

Brand: Quectel Pages: 95

Brand: ICAS Pages: 51

Brand: Icar Pages: 40

Brand: Icar Pages: 86

Brand: Icar Pages: 39

Brand: IBP Pages: 12

Brand: Rain Bird Pages: 20

Brand: xpr Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands