Rockwell Automation Allen-Bradley 1790D-N0C2 Manual Download Page 58

Page: 58 / 64

Rockwell Automation Publication 1790-UM001B-EN-P - April 2021

Appendix A Install, Wire, and Configure PROFIBUS Modules

9. Set the Watchdog Time Base and Current Range.

10. Save the configuration file.

Download the Configuration

To download the configuration to the module, follow these steps:

1. Make sure that the serial communication cable is connected between the

PC com port and the scanner serial port.

2. Verify that the processor is in Program mode.
3. Use the SST PROFIBUS configuration tool to connect to the master.

A. Click the SLC

Addresses tab.

B. Choose the Input.

This example uses
the I Type input.

A. Click the Ext. Prms tab.

B. Use the pull-down menu

to change the Watchdog
Time Base.

C. Use the pull-down menu to

change the Current Range.

D. Click OK when finished.

A. Right-click the master to

see the pull-down menu.

B. Click Connect.

Summary of Contents for Allen-Bradley 1790D-N0C2

































































Search results

Summary of Contents for Allen-Bradley 1790D-N0C2

Reviews:

Related manuals for Allen-Bradley 1790D-N0C2

Brands by name

Popular brands

Rockwell Automation Allen-Bradley 1790D-N0C2, Manual

Search results

Summary of Contents for Allen-Bradley 1790D-N0C2

Reviews:

Related manuals for Allen-Bradley 1790D-N0C2

Brands by name

Popular brands