manualshive.com logo in svg

Rockville KRYPTON MF3, Owner'S Manual

Share
Download
Rockville KRYPTON MF3 Owner'S Manual Download Page 15

15

Additional Features

Please note:

 These features apply to all models unless otherwise specified.

• Painted Conformal Coating PCB Board (Uses 2577 Waterproof Glue) 
• Rustproof Aluminum heat sink with black hairline finish
• Stainless steel end panels are rustproof 
• All screws and mounting hardware are stainless steel and rustproof
• Bottom panel is aluminum and rustproof
• Marine public address system with microphone with talkover function
• All channels on the amp have crossovers so they can each be used for subs or full range speakers or tweeters or midrange speakers
• All channels on the amplifier are bridgeable
• Digital Voltage Display on Amp
• Fully Adjustable 12dB / Octave Crossover with Differential Circuitry
• 2CH/4CH Input Mode Switch
• 8 Volt Preamp Circuitry
• Under Voltage Protection at 10V
• Over Voltage Protection at 16V 
• High-Speed MOSFET Power Supply
• Full IC-Controlled Protection Circuitry
• Fully Adjustable 12dB Bass Equalizer
• Adjustable Input Level Control
• Studio-Grade Bipolar Output Stage Transistors 
• Mute and Delay Soft Start System                       
• Status Mode LED Indicators
• Includes PA microphone

Summary of Contents for KRYPTON MF3





























Reviews:

No comments

Brands by name

Popular brands

Load more brands