Rockford Fosgate Power BD1000.1 Operating & Installation Download Page 2

i

Dear Customer,
Congratulations on your purchase of the world's finest brand of car audio amplifiers.
At Rockford Fosgate we are fanatics about musical reproduction at its best, and we
are pleased you chose our product. Through years of engineering expertise, hand
craftsmanship and critical testing procedures, we have created a wide range of 
products that reproduce music with all the clarity and richness you deserve.
For maximum performance we recommend you have your new Rockford Fosgate
product installed by an Authorized Rockford Fosgate Dealer, as we provide 
specialized training through Rockford Technical Training Institute (RTTI).  
Please read your warranty and retain your receipt and original carton for possible
future use.
Great product and competent installations are only a piece of the puzzle when it
comes to your system. Make sure that your installer is using 100% authentic
installation accessories from Connecting Punch in your installation. Connecting
Punch has everything from RCA cables and speaker wire to Power line and battery
connectors. Insist on it! After all, your new system deserves nothing but the best.
To add the finishing touch to your new Rockford Fosgate image order your Rockford
wearables, which include everything from T-shirts and jackets to hats and 
sunglasses.
To get a free brochure on Rockford Fosgate products and Rockford accessories, in
the U.S. call 480-967-3565 or FAX 480-967-8132. For all other countries, call
+001-480-967-3565 or FAX +001-480-967-8132.

PRACTICE SAFE SOUND™

CONTINUOUS EXPOSURE TO SOUND PRESSURE LEVELS OVER

100d

B MAY CAUSE PER

-

MANENT HEARING LOSS

HIGH POWERED AUTOSOUND SYSTEMS MAY PRODUCE SOUND

PRESSURE LEVELS WELL OVER

130d

B

USE COMMON SENSE AND PRACTICE SAFE SOUND

.

If, after reading your manual, you still have questions regarding this product, we
recommend that you see your Rockford Fosgate dealer. If you need further 
assistance, you can call us direct at 1-800-669-9899. Be sure to have your serial
number, model number and date of purchase available when you call.

The serial number can be found on the outside of the box.  Please record it in the
space provided below as your permanent record.  This will serve as verification of
your factory warranty and may become useful in recovering your amplifier if it is
ever stolen.

Serial Number: __________________________________

Model Number:__________________________________

Visit our website for the latest information on all Rockford products.

Summary of Contents for Power BD1000.1





























Reviews: