Rockford Fosgate Power 250.1 Operation & Installation Download Page 58

Page: 58 / 61

Stereo/Mono Betrieb

• Chinch Eingänge des rechten und linken Kanales anschlieben
•

Signal Eingangsschalter

auf “unbalanced” für den Betrieb mit Chinch-Kabel stellen

•

Linken Phasen Schalter

auf 0

stellen

•

Rechten Phasen Schalter

auf 180

stellen für den Stereo/Mono Betrieb

• Die Lautsprecher-Phase des rechten Kanales umkehren, um eine Phasenkorrektur zu

erreichen

•

Gain Regler

des linken Kanales angleichen, um die Lautstärke des Subwoofers

einzustellen

•

Impendanz

für jeden Kanal sollte minimum

2 Ohm betragen

•

Impendanz

im Brückenbetrieb sollte minimum

4 Ohm betragen

• XCard sollte auf Full Range gesteckt werder
•

Passive Frequenzweichen

werden für korrekte Stereo/Mono Operationen benötigt

– 55 –

Unbal.

Pass

Thru

Bal.

Input

-180

E Z - 1 8 0

- 0

Bridged

Gain

Bal.

Gain

–

RCA

Input

–

Ω

min.

–

Speaker

Terminal

–

Speaker

Terminal

Speaker

+ L –

Speaker

– R +

L (Mono)

Ω

min.

Ω

min.

EUTSCH

Summary of Contents for Power 250.1






























































Search results

Summary of Contents for Power 250.1

Reviews:

Rockford Fosgate Power 250.1, Operation & Installation, Page: 58 / 61

Search results

Summary of Contents for Power 250.1

Reviews: