Robustel GoRuggedR 3000 User Manual Download Page 62

Page: 62 / 83

Robustel GoRugged R3000 User Guide

RT_R3000_UG_v01.01
Confidential

15.03.2013

61 /
82

Modbus ASC

Ⅱ

slave: router connects to slave device which works under

Modbus ASC

Ⅱ

protocol.

Modbus RTU master: router connects to master device which works under
Modbus RTU protocol.
Modbus ASC

Ⅱ

master: router connects to master device which works under

Modbus ASC

Ⅱ

protocol.

Modbus

Slave

Modbus

Add the Modbus slaves which will be polled by Modbus master (router). This
section only displayed when you select “Modbus RTU master” or “Modbus
ASC

Ⅱ

master” in “Attached serial device type”.

Null

Slave Address

This connection is usually used to connect to the Modbus slave devices
which as TCP server.Enter IP address of the TCP server.

Null

Slave Port

Enter the port number of TCP server.

Null

Enter the ID number of TCP server.

Null

Summary of Contents for GoRuggedR 3000




















































































Search results

Summary of Contents for GoRuggedR 3000

Reviews:

Related manuals for GoRuggedR 3000

Brands by name

Popular brands

Robustel GoRuggedR 3000, User Manual

Search results

Summary of Contents for GoRuggedR 3000

Reviews:

Related manuals for GoRuggedR 3000

Brands by name

Popular brands