ROBOTIQ PALLETIZING SOLUTION AX Series Instruction Manual Download Page 98

Page: 98 / 115

7.3. AirPick Vacuum Gripper

The Vacuum Gripper only requires external maintenance with limited downtime. Maintenance is required after specified usage,
measured in cycles (workpiece pick-up and release) or use time (hours).

Warning

Unless specified, any repairs done on the Vacuum Gripper will be done by Robotiq.

Operation

Daily

Monthly

1 M cycles or

1000 hours

Gripper Cleaning

Dirty

conditions

Normal

conditions

Periodic Inspection

Info

For more details about the AirPick Vacuum Gripper maintenance, please consult its instruction manual available at

robotiq.com/support

Summary of Contents for PALLETIZING SOLUTION AX Series




















































































































Search results

Summary of Contents for PALLETIZING SOLUTION AX Series

Reviews:

Related manuals for PALLETIZING SOLUTION AX Series

Brands by name

Popular brands

ROBOTIQ PALLETIZING SOLUTION AX Series, Instruction Manual

Search results

Summary of Contents for PALLETIZING SOLUTION AX Series

Reviews:

Related manuals for PALLETIZING SOLUTION AX Series

Brands by name

Popular brands