background image

Chapter 5-1

 Setting the Weekly Program (RL2000 only) 

Chapter 5 

Setting the Weekly Program  

 

 

(RL2000 only) 

5.1  Setting the weekly mowing program 

 

Never let Robomow operate without 
supervision.  
Serious injury can occur.   
If the current date and time are not set 
correctly or are failed to be set when 
prompted, the times scheduled for 
automatic departure will not be correct. 
Incorrect departure times can be dangerous 
if children, pets or bystanders are present in 
the mowing area.

 

For best cutting results, set the weekly program, 

so the Robomow and the sprinklers do NOT run 

at the same time.

Remove the Manual Controller from its holder.

 

P

Follow the following steps to set the Robomow’s 

weekly mowing program.

 

P

Press the 

 button at any time to return one 

step backward.

 

 

 

 

)

Press 

 within the 10 seconds  

time limit to display a shortcut to the 

Weekly Program setting.

Incorrect departure times can be dangerous if 
children, pets or bystanders are present in the 
mowing area.

 

 





 

 

­€€

 





‚



ƒ

„

…†ƒ

‡ˆ

‰

 €€€€

 

 Š­‹€

Œ‰

†

 





…

Žƒ‘ƒŠˆƒ’



 ƒ



ƒ





“ƒ”Š€

Summary of Contents for RL2000





















































































Reviews: