Robin America RG2800i Service Service Manual Download Page 58

Page: 58 / 67

– 55 –

Improper revolutions (Electronic throttle)

Engine starts but
stops suddenly.

Go to the start malfunction section

Yes

Does
not run

・

Engine revolution

does not increase.

・

Hunting

Confirm connection of
electronic throttle coupler.

Confirmed

Runs

・

Pull the recoil starter lightly with the full throttle open.

Full throttle direction

：

Throttle direction is from the air cleaner in front

towards opposite direction (towards the back)

・

Dirty or bad spark plug

・

Poor return of the choke

・

Air cleaner blockage

・

Muffler blockage

・

Bad carburetor (water contamination, blockage, etc.)

・

Lack of gasoline

・

Gasoline deterioration

・

Blockage from the tank to the carburetor

Change the carburetor

Summary of Contents for RG2800i Service



































































Search results

Summary of Contents for RG2800i Service

Reviews:

Related manuals for RG2800i Service

Brands by name

Popular brands

Robin America RG2800i Service, Service Manual

Search results

Summary of Contents for RG2800i Service

Reviews:

Related manuals for RG2800i Service

Brands by name

Popular brands