Roberts CR9931 Manual Download Page 10

Fuse

This apparatus must be protected by a 3A fuse (BS1362) in a 13A plug
(BS1363). If another type of plug is used a 5A fuse should be fitted in
the plug, adaptor or distribution board.

IF IN DOUBT - CONSULT A QUALIFIED ELECTRICIAN.

Back-up Battery (not necessary for the unit to function)

Slide the battery cover catch in the direction of the arrow. Remove the
battery cover. Fit  2 x LR03 (AAA size) or equivalent batteries into the
battery box. Replace the battery cover.
The time and alarm settings will be retained during a temporary failure
of the AC mains supply. The LED display will not be operational. The
display will be extinguished to conserve battery life, but the memory will
retain details of the time and alarm time settings.
 If your clock radio is not to be used for a prolonged period of time,
remove the battery to avoid damage by battery leakage.

The wire coloured BLUE must be
connected to the terminal marked
N or coloured BLACK.
The wire coloured BROWN must
be connected to the terminal
marked L or coloured RED.

General

Do not allow this unit to be exposed to water or steam. It is recommended
that the FM band be used wherever possible as better results in terms
of quality and freedom from interference will usually be obtained than
on the MW or LW bands.

Mains supply

Your CR9931 will operate from a supply of AC 230volts, 50Hz 

  only.

For your convenience this product is supplied with a plug which is fitted
with a fuse of the appropriate rating. If the plug supplied is not suitable
for your socket outlet, it should be removed by unscrewing the plug top,
the terminal screws, and removing the cable.
The correct style of plug to suit your household together with a correctly
rated fuse should be fitted.

IF IN DOUBT - CONSULT A QUALIFIED ELECTRICIAN

IMPORTANT. DO NOT

 make any connection to the larger terminal which

is marked with the letter E or by the safety earth symbol 

  or coloured

Green or Green-and-yellow.
The wires in the mains lead are coloured in accordance with the following
codes :-

BLUE - NEUTRAL                    BROWN - LIVE

As these colours may not correspond with the coloured markings
identifying the terminals in your plug, proceed as follows:-

9

Summary of Contents for CR9931













Reviews: