6
Connect the DMX controller to the fixture, press [ENTER] and the [UP] and [DOWN] buttons in order to display
the following items:
"Colo,EFFE,Zoom,dimr"
. Select one of them and press [ENTER].
Now you can calibrate this effect by your controller. The DMX calibration protocol are described below.
DMX calibration protocol:
Effect
Mode 1
Mode 2
Mode 3
Mode 4
"Colo."- Colour wheel channel 0
channel 7
channel
channel 9
"EFFE." -Effect wheel channel
channel 8
channel 3
channel 0
"Zoom" - Zoom
channel
channel 9
channel 4
channel
"dimr"- Dimmer
channel 3
channel 0
channel 5
channel
After having calibrated required effects, press [ENTER] to confirm (or [MODE] to cancel and return to the menu
without reset by the
"A.rES."
function) and use the
"A.rES."
function in order to write the calibration values to
the memory and to make a reset in order to check the new adjusted positions of the effects.
uPd.M.
---
Updating mode
.Using this function you can update software in the fixture via PC and serial link.
The following are required in order to update software:
- PC running Windows 95/98/000/XP or Linux
- DMX Software Uploader
- Flash cable RS232/DMX (No.13050624)
Note1
:Software update should execute a qualified person.If you lack qualification, do not attempt the update
yourself and ask for help your ROBE distributor.
Note 2
:DMX address, IP address ,programs -3 and all functions in menu "PErS" will be set to their default
values.
To update software in the fixture:
1
.Installation of DMX Software Uploader.
1.
DMX Software Uploader program is available from the ROBE web site at WWW.robe.cz.
2
.Make a new directory ( e.g. Robe_Uploader) on your hard disk and download the software to it.
3
.Unpack the program from the archive. If the Robe fixture is produced in magnetic and electronic
ballast version, name of DMX Software Uploader is the same for both versions.
2.
Fixture software updating.
1
.Determine which of your COM port is available on your PC and connect it with to the DMX input
of the fixture using the uploading cable. Do not extend this cable! Disconnect the fixture from the
other fixtures in DMX chain! Turn on the computer and the fixture. Make sure the lamp is
switched off.
2
.Switch the fixture to the update mode by selecting the option Updating mode in menu Special
Functions on the fixture control panel:SPEC-->UPd-->yES.(From this option you cannot return back
to the main menu. If you do not want to continue in software update, you have to switch off and on
the fixture to leave this option!)
3
.It is recommended that you exit all programs before running the Software Uploader.
4
.Start the Software Uploader program. Select desired COM and then click Connect button.
If the conection is OK, click Start Uploading button to start uploading. It will take several minutes to
perform software update. If the option "Incremental Update"isn´t checked ,all processors will be
updated (including processors with the same software version).
If you wish to update only later versions of processors, enable the Incremental Update check box.
Avoid interrupting the process. Update status is being displayed in the list window.
When the update is finished, the line with the text “The fixture is successfuly updated‘ will appear in
this window and the fixture will reset with the new software.
Note: In the case of interruption of the upload process (e.g. power cut), the fixture remains in the update mode
and you have to repeat the software update again.
For example: The fixture was switched off before finishing software upload. After switching the fixture on again,
the fixture is still in the update mode and the display is dark. Restart the Software Uploader program and repeat
software update from your PC.
10. Power down mode
This mode omits fixture reset after switching the fixture on and lowers motor powers of the fixture."Power down
mode" is useful in special casech.g. if the fixture is in a flight case and you want to set its DMX address without
taking it out from the case.To enter "Power down mode",press and hold [UP] and [DOWN] and at the same time
switch on the Power switch.The following message appears on the display:
"P.d.Mo."
Press [ENTER] to activate "Power down mode" without fixture reset.Now you can set features and behaviour
of the fixture by using "
A001
"menu and
"Pers.
" menu.If you want to go to the "normal operation mode",execute
fixture reset.
Summary of Contents for ColorWash 250 AT
Page 1: ... Version 1 2 ...
Page 5: ... 3 Description of the device 1 Moving head 2 Yoke 3 Front lens 4 Base ...
Page 32: ...32 ...
