manualshive.com logo in svg

Robe 1200E Color Wash, User Manual

Share
Download
Robe 1200E Color Wash User Manual Download Page 11

11

5.7 Installing top hats 

The ColorWash 1200E AT can be fitted with various types of the top hats-see chapter "Technical specifications".If you 

wish to install a top hat (optional),follow the instructions:

 

Switch the device off before installing the top hat!

Installing the top hat on the front lens-holder of the fixture:

1.Loosen 4 lens holder quarter-turn screws and hook both securing springs to the plastic projections in the front lens-holder.       

Tighten the  lens holder quarter-turn screws again.

2.Put desired top hat onto a front lens-holder and fasten it by two fastening screws.

.Snap both springs to the slots in the top hat.

5.8 Rigging the fixture

DANGER TO LIFE!

Please consider the respective national norms during the installation! 

The installation of the fixture has to be built and constructed in a way that it can hold 10 times the weight for 1 hour without 

any harming deformation.

The installation must always be secured with a secondary safety attachment, e.g. an appropriate catch net. This secondary 

safety attachment must be constructed in a way that no part of the installation can fall down if the main attachment fails.

When rigging, derigging or servicing the fixture staying in the area below the installation place, on bridges, under high 

working places and other endangered areas is forbidden.

The operator has to make sure that safety-relating and machine-technical installations are approved by an expert before 

taking into operation for the first time and after changes before taking into operation another time.

The operator has to make sure that safety-relating and machine-technical installations are approved by an expert after 

every four year in the course of an acceptance test.

The operator has to make sure that safety-relating and machine-technical installations are approved by a skilled person 

once a year.

Allow the fixture to cool for ten minutes before handling.

The projector should be installed outside areas where persons may walk by or be seated.

IMPORTANT! OVERHEAD RIGGING REQUIRES EXTENSIVE EXPERIENCE, including  calculating working load limits, 

installation material being used, and periodic safety inspection of all installation material and the projector. If you lack these 

Slot

Securing spring

Plastic projection

Securing spring

Top hat

Fastening screw

Fastening screw

Lens-holder

Summary of Contents for 1200E Color Wash







































Reviews:

No comments

Brands by name

Popular brands

Load more brands