manualshive.com logo in svg

ROBBE BLUE ARROW XL 490, Operating Instructions Manual

Share
Download
ROBBE BLUE ARROW XL 490 Operating Instructions Manual Download Page 15

15

Operating Instructions - BLUE ARROW XL 490 RTF 2.4 GHz No. S2542

Replacement parts list - Blue Arrow XL 490 RTF

Order No.  Description

S2542001  Dome bearing bracket  
S2542002  Tail boom bracket 
S2542003  Servo mount 
S2542004  Main rotor blades 
S2542005  Base plate 
S2542006  Circuit board mount 
S2542007  Battery compartment 
S2542008  Side frame 
S2542009  Tail rotor gearbox housing 
S2542010 Canopy 
S2542011  Landing gear  
S2542012  Swashplate guide 
S2542013  Outer main rotor shaft 
S2542014  Inner main rotor shaft
S2542015  Rotor blade grip 
S2542016 Pushrod 
S2542017  Tail stabiliser set  
S2542018  Tail rotor blade 
S2542019  Motor set  
S2542020  LiP battery, 11.1 V / 1600 mAh 
S2542021  Main gear set 
S2542022  Control unit 
S2542023 Swashplate 
S2542024  Tail braces 
S2542025  Servo, 9 g 
S2542026  Battery charger 
S2542027  Small parts set for rotor shaft 

When replacing components it is very im-
portant to use the correct type of cross-point 
screwdriver or allen key, and to tighten the 
screws with great care. 

Use thread-lock fluid on metal-to-metal 

joints only!

S2542025

S2542026

S2542027

S2542028

S2542029

S2542031

S2542030

Replacement parts list - Blue Arrow XL 490 RTF

Order No.  Description

S2542028 Flybar 
S2542029  Tail boom  
S2542030  Canopy support 
S2542031  Spacer set

 

Summary of Contents for BLUE ARROW XL 490


















Reviews:

No comments

Brands by name

Popular brands

Load more brands