ROBAND Haellde RG-250 diwash, User Instructions

Page: 4 / 8

USER INSTRUCTIONS
HALLDE
RG-250
(GB)
CAUTION!
Read all of the instructions before you begin
to use the machine.
Take great care not to injure your hands on
sharp blades and moving parts.
Always use the pestle when cutting through
the feed tube, and never put your hands into
the feed tube.
The 3-phase version of the RG-250 diwash
service mechanic.
be allowed to repair the machine and open
the machine housing.
Hold only the feeder plate handle when the
feeder is to be opened or closed.
The decoring device sleeve must be
tighte ned (anti-clockwise) and unscrewed
(clockwise), by means of the wrench.
Do not use the machine to cut frozen foods.
Remove all hard parts from foods before
cutting (e.g., apple stems, woody parts of
turnips, etc.) to avoid damaging the cutting
blades.
This appliance is not to be operated by
children or persons with reduced physical,
sensory or mental capabilities or persons
lacking experience of such appliances,
unless they are given adequate instruction
or supervision.
UNPACKING
Check that all of the parts have been delivered,
that the machine operates as intended, and
that nothing has been damaged in transit.
INSTALLATION
Connect the machine to an electric power
The machine should be placed on a countertop
or table that is about 650 mm high.
Locate the hanger for the cutting tools on the
and safe use.
Check the following two points without cutting
Check that the machine stops when the pusher
plate is moved up and swung out, and that it
restarts when the pusher plate is swung in
and lowered.
Check that the machine cannot be started with
plate lowered.
taking the machine into operation.
ALWAYS CHECK BEFORE USE
or open the isolating switch, and then check
that the electric cable is in good condition and
is not cracked on the outside.
Check that, with a cutting tool fitted, the
machine stops within 2 seconds when the
pusher plate is swung out to one side and
re-starts when the pusher plate has been
swung back over the feeder.
Check that the machine cannot be started with
plate lowered.
perform as intended or if the electric cable is
-
and lubricate it with a few drops of machine oil.
Check that the cutting tools are in good
con dition and are sharp.
With regard to cutting tools, see page 3.
TYPE OF PROCESSING
Slices, dices, grates, shreds, cuts julienne,
of dimensions, depending on the cutting tool
bread, cheese, nuts, mushrooms etc.
USERS
Restaurants, shop kitchens, hospitals, diet
kitchens, retirement homes, schools, fast food
ships, central kitchens, institution kitchens etc.
CAPACITY
minute.
USING THE FEEDERS
for bulk feeding of all sorts of products and
for cutting larger products such as cabbage.
The large feed compartment is also used when
such as tomatoes and lemons. Place/stack the
products as shown in the picture.
The in-built feed tube is used (picture) for
cutting long products such as cucumbers,
see picture.
ASSEMBLING
THE MANUAL FEEDER ERGO LOOP
clockwise as far as it will go (into the locked
position).
Grip the push feeder with both hands and insert
the shaft end into the mounting on the machine.
Press down the pusher plate as far as it will go.
DISMANTLING
THE MANUAL FEEDER ERGO LOOP
Raise the push feeder and swing it out to the
Grip the push feeder with both hands.
Pull up/out the pusher plate.
FITTING THE CUTTING TOOLS
Raise the pusher plate and swing it out to
the left.
Turn the locking knob anti-clockwise and raise
Place the ejector plate on the shaft and turn/
press down the ejector plate into its coupling.
Place the chosen cutting tool on the shaft and
into its position.
During dicing: place the dicing grid with the
sharp edge of the knives upward, so that the
the guide groove on the machine base. Then
into its position.
centre shaft of the cutting tool.
knob clockwise to the locked position.
REMOVING THE CUTTING TOOLS
Raise the pusher plate and swing it out to
the left.
Turn the locking knob anti-clockwise and raise
Remove the cutting tool/tools and the ejector
plate.
CLEANING
to clean the machine.
does not have a plug, open the isolating switch.
Remove all the removable parts that are to
be cleaned.