8
Gas
tap
maintenance
These
maintenance
operations
must
only
be
carried
out
by
IMPORTANT
:
Before
carrying
out
any
maintenance
operations, disconnect
the appliance from
the
gas
and
electricity
supplies
.
an
AUTHORISED
PERSON.
If
a
gas
tap
becomes
stiff
to
operate
,
then
you
should
proceed
as
follows:
◆
Remove
the
control
knobs
,
pan
supports
,
burners
,
hob
fixing
screws
and
clamps.
◆
Remove
the
hob
from
the
worktop
and
remove
any
underside
protective
covers.
◆
Disconnect
the
fixings
holding
the
tap
to
the
fascia
panel
and
separate
the
assembly
.
then
clean
the
cone
and
seating
,
with
a
cloth
dampened
with
solvent.
◆
Lightly
smear
the
cone
with
high
temperature
grease
,
reassemble
into
position
and
rotate
a
few
times.
◆
Remove
the
cone
again
and
remove
any
excess
grease
,
making
sure
that
the
gas
ducts
are
not
obstructed
with
grease.
Gas
Hob
Carefully
reassemble
the
components
and
perform
a
gas
leakage
test
.
If
it
becomes
necessary
to
tap
,
then
you
should
proceed
as
follows:
◆
Remove
the
control
knobs
,
pan
supports
,
burners
,
hob
fixing
screws
and
clamps.
◆
Remove
the
hob
from
the
worktop
and
remove
any
underside
protective
covers.
◆
Disconnect
the
fixings
holding
the
tap
to
the
fascia
panel
and
separate
the
assembly.
◆
Disconnect
the
gas
pipe
from
the
gas
tap
,
and
then
disassemble
them
from
the
gas
rail
by
removing
the
fixing screws.
◆
When
fitting
a
new
tap
,
ensure
that
a
new
gasket
is
used.
◆
Reconnect
the
gas
tap
,
perform
a
gas
leakage
test
and
then
reassemble
the
hob.
replace
a gas
My appliance isn
'
t
working
correctly
DO
NOT
ATTEMPT
TO
REPAIR
THE APPLIANCE YOURSELF.
◆
◆
The appliance must
be
accessible
for
the
engineer
to
perform
any
necessary
repair
.
If
your appliance is
installed in
such
a
way
that
an
engineer
is
concerned
that
damage
will
be
caused
to
the appliance or
your
kitchen
,
then
he will
not
complete
a
repair.
◆
This
includes
situations
where appliance have
been
tiled
in
,
sealed
in
with
sealant
,
have
wooden obstructions
placed
in
front
of
the appliance, like
plinths, or
any
installation
other
than
the
one
specified
by
ROBAM APPLIANCES
CO
.,
LTD.has
been
completed.
◆
Please
refer
to
the
conditions
of
guarantee
that
appear
on
the
warranty
card
that
you
receive
with
the appli ance.
◆
IMPORTANT
:ROBAM APPLIANCES
CO
.,
LTD.operates
a
policy
of
continuous
improvement
and
reserves
the
right
to
adjust
and
modify
its
products
without
prior
notification
.
Please
note
that
if
an
engineer
is
asked
to
attend
whilst
the
product
is
under
guarantee
and
finds
that
the
problem is
not
the
result
of
an appliance fault
,
then
you
may
be
liable
for
the
cost
of
the
call
out
charge.
Note:
◆
the
cook
top
must
be
installed
with
provision
to
allow
the
gas
to
be
turned
off
and disconnected
for
servicing
and removal
of
the
appliance
as
required
from
gas
supply.
◆
The gas pressure must be set by an approved gas fitter and a full operational test and a test forpossible
leakages must be carried out by the gas fitter after installation.
◆
The gas pressure must be set by the approved gas fitter as shown on the data plate natural gas 1kPa.
◆
Minimum flow adjustment is no need, because minimum flow has been adjusted when manufacturing.If the
minimum flow is not working properly, please contact local dealer to solve the problem.contact information
see“After Sale Service”
