RRDS100
Rear Deck Scrolling Digital LED Message System
Dear Customer,
CONGRATULATIONS. The RRDS100 Rear Deck Scrolling Digital LED Message
System, when used as described, will give you years of dependable service in
your car, truck, RV, or mini-van. We have taken numerous measures in quality
control to ensure that your product arrives in top condition and will perform
to your satisfaction. In the rare event that your RRDS100 Rear Deck Scrolling
Digital LED Message System contains a damaged or missing item, does not
perform as specified, requires warranty service, or you have an installation
problem,
DO NOT RETURN THIS PRODUCT TO THE STORE. PLEASE CALL
OUR TOLL FREE NUMBER FROM THE U.S.A. AND CANADA 1-800-445-1797
and ask to speak with a member of our technical service team; or submit your
questions by e-mail to [email protected] and a member
of our technical service team will respond by e-mail to your questions. Our
in-house technical service team will expedite delivery of your part, advise you
on installation, or help troubleshoot a problem with you. If your product needs
warranty service, our technical service team representative will help you obtain
the fastest remedy possible under the warranty.
Parts
Installation
Operation
Operation
Before You Start
Recommended Mounting
1. Before mounting permanently, it is recommended that you have someone
hold the RRDS100 in place so that you can see how it looks from outside
the car.
2. Check the power cable length to ensure the 12V adaptor will reach to the
closest 12V power supply jack.
3. Ensure the IR sensor and red action indicator are visible from your rear view
mirror.
4. Prepare mounting area with a glass cleaner.
5. Remove paper from one side of the adhesive mounting pad and secure
pads to the recessed surface of the mounting feet. Once pads are secured
to the mounting feet, remove paper from the exposed side of both pads
and secure unit to the glass surface in the desired location. Note: If you
must relocate the unit after mounting you will need to replace the mount-
ing pads.
6. Rotate housing so that the display can be easily viewed.
7. Run the 12V adaptor cable along the edge of the car’s seals to the 12V
power supply jack. Note: Ensure that the cable is installed so that passen-
gers will not trip over it when entering and exiting the vehicle.
Program And Save A Message
The RRDS100 has 99 pre-programmed that you may edit and save in memory.
(SEE Library of Words and Phrases)
1. To enter text press EDIT
2. Last message will be displayed, to remove text press ERASE, to clear entire
message press DOWN.
3. Use alphanumeric Buttons to input required character. Press same button
quickly to advance through characters, wait 1 second to use same letter
again, or press next required character.
4. To insert a library word or phrase, press LIBRARY followed by the library
number ie: 06 or 41 etc.
5. To insert a space press SPACE. To change characters to lower case press
SHIFT.
6. Once you have completed a message press PLAY once to check this mes-
sage. If you are unhappy with this message then press EDIT again to dis-
play the message for alteration.
7. After a modification press PLAY again to display your message (only press
play once).
8. If your are satisfied with the message you have created, store your message
in the Pre-set Memory Buttons by pressing STORE followed by one of 10
Pre-set Memory Buttons, MO to M9 or BANNER of your choice.
9. Your message is now stored in this memory location and can be replayed
at any time by simply pressing this memory button.
Note: The message board has a maximum memory capability of 470 char-
acters. Up to 80 characters can be programmed into memory locations,
however the total sum of the messages stored cannot exceed 470.
Profanity Filter
The RRDS100 message board has a built-in filter which prevents the use of
some words (profanity). Most profanity will be displayed as ****.
Playing Messages
1. To play a message stored on a Pre-set Memory Button: press M0 to M9.
2. To play a word or phrase stored in the Words and Phrases Library: press
LIBRARY followed by the library number, ie: 06 or 41 etc.
3. To play the banner message press BANNER
4. To play the current message continuously: press ONLY
5. To play messages backwards: press MIRROR
Programming a Sequence Of Messages
Up to 16 messages can be replayed in a sequence from the
memory of the unit.
To program a sequence:
1. First clear all stored messages to ensure no unwanted messages are
included. Press SETUP followed by ERASE.
2. Play required messages from Memory keys, Banner message or Library
phrases in the order required.
3. To remove last played message from sequence press ERASE
4. Once you have played the sequence of messages you require, press PLAY
to play sequence once, or PLAY/PLAY to repeat sequence continuously.
5. To turn off the message scroller press CANCEL
6. To save message sequence for next power up press SETUP, then STORE
Adjusting The SPEED Of The Display
To increase the speed of the display:
1. Press SPEED, followed by UP; continue to do this until required speed is
achieved.
Digital LED Message Board
Remote Control
Read and follow these instructions carefully before installing or using the
Electronic Message Board System.
• Always use the 12 Volt Adaptor to supply power to the RRDS100.
• Never connect directly to your car’s battery or fuse block, as the adaptor con-
tains a safety fuse that should not be bypassed.
• Turn OFF any device in your vehicle as this device’s remote control may interfere
with other devices operated by remote control. Other device’s remote controls
may interfere with this device.
• Do not cover the vents on the ends of the RRDS100 as overheating may occur.
• Keep your RRDS100 away from moisture and excessive humidity. It should be
mounted inside the vehicle only.
• Clean with a dry cloth only.
• Do not program messages while driving.
• Obey all local, state, and federal traffic laws regarding the use of this product.
• For best viewing, remove window tinting in the mounting area.
Turning Power On and Off
1. Start vehicle or turn ignition to accessory position to operate unit.
2. Turn OFF any device in the vehicle that can be operated by remote control.
3. Insert the 12 Volt adaptor plug into the vehicle’s 12 Volt power port/Cigarette
lighter socket. The current banner message will be displayed.
4. To turn the unit OFF, remove the adaptor from the receptacle.
IR Remote Control Sensor
The Rear Deck Scrolling Digital Message System has an
IR Sensor on the back of the unit.
Do not block the sensor, this sensor allows the remote
control to control the unit.
Mounting Pads
Remote Control
1. Remove the remote’s battery compartment
cover.
2. Insert the two AAA batteries provided being
sure to maintain polarity, follow the positive
and negative orientation indicated in the bat-
tery compartment.
3. Replace the battery compartment cover.
NOTE: This device’s remote control may interfere with other devices operated
by remote control. Other device’s remote controls may interfere with this
device.
IR Sensor
Activity Indicator
GIVE US A CALL, WE'LL HELP YOU INSTALL.
1-800-445-1797
PLEASE DO NOT RETURN PRODUCT TO STORE.
Visit us on the WEB
www.roadmasterusa.com
For Information and Technical Assistance,
Call Toll-Free in U.S.A. and Canada.