background image

 

 

User's Guide AEB4/8-I

 

6

 

 

 

 
 
 

 
 
Connecting an AEBx-I to the second ADAT In of 
a HDSP 9652. Remove the jumper ST5, plug 
DIGOUT of the AEBx-I on both right and middle 
pin of ST5. 
 
 
 
 
 
 
 

 
 
 
 
 
 
 
When using two AEBx-I, the PCI card’s word 
clock signal will be daisy chained through the 
AEBs. For this to work, connect ST7 of the 
HDSP 9652 with ST7A of the first AEB. Then 
connect ST7B of the first AEB with ST7A of 
the second AEB.

 

 
 
 
 
 
 
 
6. Alternative Installation

 

 
Installation is done comfortably as described using the attached bracket. Alternatively it is pos-
sible to mount the AEB at a different place inside the computer using the supplied nuts. This 
requires to drill 4 holes into the housing. 
 

RME does not accept claims for damages of any kind when installing the AEB in this 
way! Modifications to the housing should be done by qualified technicians only, and 
only after having removed all components from the housing (danger of short circuit 
by metal splinter etc).

 

 

1.  

Remove the bracket from the AEB (2 screws). 

2.  

Carefully check that the desired location offers a flat plane, is free from any voltage carrying 
devices or cables, and that the AEB does not get in contact with other devices even when 
the housing is closed. 

3.  

Please note that the lenght of the supplied cables does not allow any distance to the DIGI 
card. 

4.  

Drill 4 holes, diameter 0.5" (13 mm), distance of 0.75" (19.05 mm) each, at the desired 
place (see drill template). 

5.  

Fit the AEB into the holes and fix it with the supplied nuts. 

 

Summary of Contents for AEB4-1










Reviews: