background image

 

Model GP-01 Operator’s Manual

Introduction • 5

Introduction

Using an advanced microprocessor controlled detection system, the Model 
GP-01 Single LEL Gas Monitor detects the presence of combustible gas 
(e.g., methane, CH

4

) as a percentage of LEL (lower explosive limit). The 

Model GP-01’s compact size and easy-to-use design makes it ideally 
suited for a wide range of applications, including sewage treatment plants, 
tunnels, hazardous waste sites, petrochemical facilities, oil fields, mines, 
and chemical plants. The Model GP-01 is even small enough to be placed 
conveniently in a pocket. The Model GP-01 offers the following features: 

Compact design

Fast, accurate response with digital liquid crystal display (LCD)

Visual, audible, and vibration alarms

Microprocessor control for reliability, ease of use, and advanced 
capabilities 

Peak readings

Gas, battery, sensor failure, and system failure alarms

CSA certified for intrinsic safety in Class I, Division I, Groups A, B, C, 
and D hazardous atmospheres

WARNING: The Model GP-01 detects combustible gas, which can be 

dangerous or life threatening. When using the Model GP-
01, you must follow the instructions and warnings in this 
manual to assure proper and safe operation of the unit 
and to minimize the risk of injury.

Summary of Contents for GP-01


































Reviews: