RKI Instruments GasWatch 3 Operator'S Manual Download Page 71

Page: 71 / 95

GasWatch 3 for CO and O

Chapter 5: User Mode and Calibration • 71

5. Press and release POWER/MODE. The Set Password Screen appears. The current

password appears and the first digit flashes.

6. Use AIR to display a number from 0 to 9.
7. Press and release POWER/MODE to enter the selection and advance to the next number.

To go back a number, press and hold AIR and POWER/MODE for a few seconds.

8. Repeat Step 6 and Step 7 to select the remaining numbers. When you press and release

POWER/MODE to enter the last number, the password is saved and the instrument returns

to the

PASS-W

item in User Mode.

9. See “Entering Measuring Mode (START)” on page 72 to enter Measuring Mode.

Viewing the ROM/SUM (ROM/SUM)

The

ROM/SUM

screen shows the instrument’s firmware version and firmware checksum.

1. While in User Mode, press AIR to scroll to

ROM/SUM

2. Press and release POWER/MODE. The screen cycles through the main board’s ROM/

SUM and the sensor board’s ROM/SUM. The ROM is the top value and the SUM is the

bottom value.

3. Press and release POWER/MODE to return to the

ROM/SUM

item in User Mode.

4. See “Entering Measuring Mode (START)” on page 72 to enter Measuring Mode.

PASS - W

0 4 0 5

ROM / SUM

d671

5822

Summary of Contents for GasWatch 3
































































































Search results

Summary of Contents for GasWatch 3

Reviews:

Related manuals for GasWatch 3

Brands by name

Popular brands

RKI Instruments GasWatch 3, Operator'S Manual

Search results

Summary of Contents for GasWatch 3

Reviews:

Related manuals for GasWatch 3

Brands by name

Popular brands