background image

 

 

Statement of Warranty

Statement of Warranty

Statement of Warranty

Statement of Warranty    

 

RJM & Associates, LLC warrants its products for a period of three (3) years from 
the date of shipment to be free from defects in materials and workmanship and 
meets applicable published specifications. Equipment which has been operated 
within  its  ratings  and  has  not  been  subjected  to  mechanical  or  other  abuse  or 
modification by the purchaser, its agents, and/or employees, will, at the option of 
RJM,  be  replaced  or  repaired  if  it  is  returned,  freight  prepaid,  to  RJM  & 
Associates,  LLC.  Equipment  that  fails  under  conditions  other  than  described 
herein will be repaired at the price of components and labor in affect at the time 
of repair. 

 

This warranty is in lieu of all other warranties, expressed or implied, with respect 
to the condition or performance of any RJM product, its merchantability or fitness 
for a particular purpose. RJM is not liable for any consequential damages. 

 

FCC Compliance

FCC Compliance

FCC Compliance

FCC Compliance    

 

This equipment has been tested and found to comply with the limits for a Class A 
digital device pursuant to Part 15 of the FCC Rules. These limits are designed to 
provide  reasonable protection against harmful interference when the equipment 
is operated in a commercial environment. This equipment generates, uses, and 
can radiate radio frequency energy and, if not installed and used in accordance 
with  the  instruction  manual,  may  cause  harmful  interference  to  radio 
communications.  Operation  of  this  equipment  in  a  residential  area  is  likely  to 
cause harmful interference in which case the user will be required to correct the 
interference at his own expense. 

 

Copyright

Copyright

Copyright

Copyright 

© 2014  RJM & Associates, LLC 

Contents of this publication may not be reproduced in any form without the 
written permission of RJM. Reproduction or reverse engineering of copyrighted 
software is prohibited. 

 

 

 

July 2014 
Part Number  71

71

71

71----00

00

00

0023

23

23

23 

Summary of Contents for ARTS-201B



























Reviews: