background image

Check for parts online at 

www.HuntRiversEdge.com

 or call 800-450-EDGE (3343) M-F 8-5

7

Operator's Manual

Rivers Edge® Uppercut™

Figure 3

ladder side rails

steel washers

1/4-20 x 2" bolt

locknuts

right 

armrest

backrest mounts

1/4-20 x 3" bolts

left  

armrest

1/4-20 x 

2-1/4" bolts

1/4-20 x 2" 

bolts

4.  Attach the front of the ladder side rails (410053) to the front platform 

using (2) provided 1/4-20 x 2” bolts, locknuts and (4) steel washers. 

SEE FIGURE 3.

5.  Attach the left armrest (410062L), right armrest (410062R) and (2) 

backrest mount tubes (410082) to the previously assembled ladder 

side rails and platform support rails using (2) provided 1/4-20 x 2” 

bolts, (4) 1/4-20 x 2-1/4” bolts, (2) 1/4-20 x 3” bolts, (8) locknuts and 

(8) steel washers. 

SEE FIGURE 3.

6.  Attach the upper tree blade (10162) to the ladder side rails using 

(4) provided 1/4-20 x 2-1/4” bolts, locknuts and steel washers. 

SEE 

FIGURE 4.

7.  Attach the lower tree blade (10164) to the inside of the platform 

support rails using (4) provided 1/4-20 x 2-1/4” bolts, locknuts and 

steel washers. 

SEE FIGURE 4.

8.  Attach footrest (410061) to ladder side rails using (2) provided 1/4-20 x 

2-3/4” bolts, locknuts, steel washers and nylon spacers. 

SEE FIGURE 5.

  

Figure 4

upper tree blade

ladder 

side rails

1/4-20 x 

2-1/4" bolts

lower tree 

blade

1/4-20 x 2-1/4" bolts

locknuts

steel washers

1/4-20 x 

2-3/4" bolts

footrest

steel 

washers

locknuts

nylon 

spacers

Figure 5

Summary of Contents for Uppercut RE632





















Reviews: