Rivers Edge Landmark LM600 Operator'S Manual Download Page 17

Page: 17 / 24

Check for parts online at

www.HuntRiversEdge.com

or call 800-450-EDGE (3343) M-F 8-5

Operator's Manual

Landmark

™

Permanent Blind

2. Insert the six R1 poles (window tube supports) into the

window sewn sleeves found on the one back and two side

wall panels. You will use two tubes per panel. SEE INSIDE

BACK PANEL AND INSIDE SIDE PANEL FIGURES.

3. Insert the P1 and Q1 poles (male and female door tubes) into

the door sewn sleeves found on the left and right front wall

panels. You must insert a male from one end of the sleeve

and a female from the other end and carefully meet the

tubes in the middle and slide together. This must be done

by feel as you will not be able to see the tubes as they will

be inside the sewn sleeve. SEE INSIDE RIGHT FRONT AND

INSIDE LEFT FRONT FIGURES.

4. Hang the back wall panel (29) on the back side of assembled

steel frame (opposite the door opening) by securing five

Velcro loops located across the top of the back wall panel

to the assembled A1 and B1 poles. Secure the two window

Velcro loops to the assembled D1 and E1 poles as well. SEE

INSIDE BACK PANEL FIGURE AND FIGURE 14.

5. Hang the two side wall panels (25) on the two sides of

assembled steel frame by securing five Velcro loops located

across the top of the side wall panels to the assembled

H1 and

1 poles. Secure the two window Velcro loops to

the assembled D1 and E1 poles as well. SEE INSIDE SIDE

PANEL FIGURE.

6. Hang the right and left front wall panels (30 and 31) on the

front side of assembled steel frame by securing two Velcro

loops located across the top of each front panel to the

assembled A1 and B1 poles. You will also need to secure

the plastic C-clips found on each end of the previously

assembled P1 and Q1 poles to the top and bottom of

assembled steel frame. SEE FIGURE 15.

7. Pull all panels tight by wrapping D-ring straps around

assembled C1 or G1 poles. Feed the long strap through both

D-rings and back through to tighten. SEE FIGURE 16 A-D.

8. Secure all panels together in the corners by matching up the

Velcro strips. Start at the top of the Velcro strips and working

your way to the bottom. Adjust and redo as necessary to

accomplish a snug fit and take out as much slack in the fabric

panels as possible. SEE FIGURE 17 A.

9. Drape the roof panel (24) over the assembled roof frame.

Match up the Velcro strips on front and back of roof panel to

the front and back wall panels. Adjust and redo as necessary

to take out as much slack in the fabric as possible.

SEE FIGURE 17 B.

FIGURE 14

FIGURE 15

FIGURE 17

FIGURE 16

Summary of Contents for Landmark LM600
























Search results

Summary of Contents for Landmark LM600

Reviews:

Related manuals for Landmark LM600

Brands by name

Popular brands

Rivers Edge Landmark LM600, Operator'S Manual

Search results

Summary of Contents for Landmark LM600

Reviews:

Related manuals for Landmark LM600

Brands by name

Popular brands