RiverGrille TF2048902-RG-00 Assembly, Use And Care Download Page 8

TF2048902-RG-00                                             

            Page 8 of 16                                                      20161123 V.1 

NOTE: If you cannot complete connection, disconnect regulator and repeat step 5 and 6. If 
you are still unable to complete the connection, 

do not use this regulator! 

 

Disconnecting Regulator to the LP Tank 

1.  Turn control knob of regulator to the OFF position. 
2.  Turn LP tank OFF by turning hand wheel clockwise to a 

full stop

3.  Turn the coupling nut counterclockwise to loosen the connector. Loose by hand only 

– do 

not use tools. 

4. 

When disconnected, the regulator should be hung on the hook attached to the appliance

.

 

 

 

WARNING 

 

 

Do not insert any tool or foreign object into the valve outlet or safety relief valve. You may 
damage the valve and cause a leak. Leaking propane may result in explosion, fire, severe 
personal injury, or death. 

 

Never attempt to attach this appliance to the self-contained LP gas system of a camper or 
trailer or motor home. 

 

The pressure regulator and hose assembly supplied with the appliance must be the one 
used. Replacement pressure regulator and hose assemblies must be those specified by 
the manufacturer. 

 

 

WARNING 

 

 

Do not use appliance until leak checked.

 

 

If leak is detected at any time, STOP.

 

 

If you cannot stop a gas leak, immediately close LP tank valve, leave area of appliance, 
and call LP gas supplier or your fire department!

 

 
Leak Testing Valves, Hoses and Regulator 

1.  Turn all control knob(s) to OFF. 
2.  Be sure the regulator is tightly connected to LP tanks. 
3.  Completely open LP tank valve by turning hand wheel counterclockwise. If you hear a 

rushing sound, turn gas off immediately. There is a major leak at the connection. Correct 
before proceeding. 

4.  Brush soapy solution onto indicated connections shown below in A and B. (Reference 

connection of hose to burner on page 13.) 

5.  If 

“growing” bubbles appear, there is a leak. Close LP tank valve immediately and 

retighten connections. If leaks cannot be stopped, do not try to repair. Call for 
replacement parts. Order new parts by giving the serial number, name and number of 
items needed to the Customer Service Center at 

– 888 – 837 – 1380

 Use only 

replacement parts specified by manufacturer. 

6.  Always close LP tank valve after performing tank test by turning hand wheel clockwise. 
 
 
 
 
 
 
 
 
 
 

 

 

Summary of Contents for TF2048902-RG-00

















Reviews: