Riverbed 8000 Rack Installation Manual Download Page 7 | Manualshive

Page: 7 / 28

background image

Rack Installation Guide

7

Mounting Series 1050 and 2050 to a Rack

Rack Installation Guide

“Mounting the System to a Four-Post Rack” on page 10

“Mounting the System to a Two-Post Rack” on page 12

To open the bezel on Series 1050 and 2050 systems

To open the bezel firmly press in the buttons on each side of the bezel and slide it towards you. The
bezel remains attached to the system on hinges.

Figure 3. Opening the Bezel on Series 1050 and 2050 Systems

Mounting the RMK-002A Rails for 1050 and 2050 Systems

The RMK-002A rails are modified rails for 1U xx50 systems, the following section describes how to mount
a 1050 and 2050 system to a four-post rack with these rails.

«
...
5
6
7
8
9
...
»

Summary of Contents for 8000





























Reviews:

No comments

Related manuals for 8000

Brand: Rane Pages: 8

Brand: Rane Pages: 4

Design Mixer Advanced Electronic

Brand: Gastroback Pages: 72

Brand: AirTurn Pages: 25

CONVERGE Matrix

Brand: Clear One Pages: 24

Brand: ALLEN & HEATH Pages: 11

Brand: PedalPCB Pages: 5

Brand: Shaman Pages: 2

Brand: VocoPro Pages: 7

Brand: PuzzleSounds Pages: 15

Brand: Peavey Pages: 16

Brand: Adler Europe Pages: 52

Pasta Prof PL10S

Brand: R.G.V. Pages: 52

Brand: MIKA Pages: 7

Brand: IBM Pages: 36

Brand: GE Pages: 10

Brand: GE Pages: 20

Brand: GE Pages: 40

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands