RiTTO TWINBUS System Manual Download Page 38 | Manualshive

Page: 38 / 197

background image

Inst

alla

tion

Installation: Assembly, connection and start-up

38

Delete settings

This function deletes all settings and programmed bell buttons. If necessary, please note down any existing customer
settings before deleting the settings.

If the settings have not been deleted:

Check on the TwinBus power supply unit whether the setting protection is activated - see page

Repeat the procedure.

2.5.2 TwinBus comfort indoor telephone 1 7650

Assembly

Remove the TwinBus device and the supplied components from the packaging.

Please provide your customers with a copy of the operating instructions for the TwinBus device. The operating
instructions are printed on the packaging or are enclosed with the unit.

Activity

Result

✔

Short tone: Settings have been deleted.

/

Long tone: Settings have not been deleted.

Press and hold for 5 s
until

+

Acoustic signal for confirmation

!

00037-0

«
...
36
37
38
39
40
...
»

Summary of Contents for TWINBUS






































































































































































































Reviews:

No comments

Related manuals for TWINBUS

Brand: ABB Pages: 58

Brand: ABB Pages: 191

JBL BAR 5.0 MULTIBEAM

Brand: Harman Pages: 25

Brand: Jensen Pages: 2

Brand: Panasonic Pages: 4

Brand: Kicker Pages: 9

Brand: NAIM Pages: 31

Brand: GCAN Pages: 12

Brand: Sonifex Pages: 68

Brand: Omron Pages: 114

Brand: August Pages: 6

Brand: VIEWONHOME Pages: 21

Brand: Yaesu Pages: 5

Brand: Elvox Pages: 16

ZEB Juke Bar 2601

Brand: Zebronics Pages: 19

Compact FLASH III

Brand: ACS Pages: 37

Brand: Emerson Pages: 22

Brand: Emerson Pages: 22

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands