1
Direct Receiver Discriminator
14
2
15
3
TX Audio
16
4
17
5
TX LTR (D)QC Data
18
6
Transfer Control
19
7
TX PTT Output
20
8
21
9
22
10
23
11
24
Power Supply Ground
12
25
13
11 – 16 Volts
N/C Cable Shield
1
3
25
1
1
TxK
24
3
MON
23
4
GND
22
5
6
2
0
7
19
6
18
5
17
V+ 4
16
3
15
2
14
1
Raider
Raider
Raider
Raider
Raider
DB-25 Male
DB-25 Male
DB-25 Male
DB-25 Male
DB-25 Male
RRX-450
RRX-450
RRX-450
RRX-450
RRX-450
DB-25 Female
DB-25 Female
DB-25 Female
DB-25 Female
DB-25 Female
Ritron RRX-450/452/460 Repeater Interface
to Trident Raider/ Marauder
This RRX–RMC cable is available directly from RITRON
Contact RITRON for specific details
W22/ W30 = DISC INPUT GAIN SET (i.e.: input audio from RRX to CNTRLR.), > 2V
P-P (see page 28, SQUELCH LEVEL), U1–1.
*
W26 OUT can lead to distortion problems on the "TX AUDIO OUTPUT" (Trident Pin
3). This will likely require a resistor (~36
+k), across high gain feedback resistor R15
(100k or 220k) in circuit, or in series with low gain 10k resistor (across W26 pins).
Raider/ Marauder
DB-25
RRX-450/452/460
DB-25
EXTERNAL VIEW OF FEMALE PANEL CONNECTOR SAME AS
INTERNAL VIEW OF MALE CABLE CONNECTOR
NOTES:
"I" = Input; "O" = Output.
See RRX–MRM (RRX Technical Manual) for Ritron cable color code.
I
O
O
I
O
I
O
I
O
I
I
O
I
O
1 A Fuse on
RRX Control
Board
+12 V
IN
OUT
OUT
*
ON
;
OFF
:
ON
;
ON
;
W22 W30 W26 TX DTA RX DTA TX DCS RX DCS
Raider Jumpers
Raider Invert Switches
Pub. No. 14560028 Rev. A 00–08
( Page 1 of 1 )
T
T
T
T
The RRX
he RRX
he RRX
he RRX
he RRX m
m
m
m
must
ust
ust
ust
ust be pr
be pr
be pr
be pr
be pro
o
o
o
og
g
g
g
gr
rr
rrammed with
ammed with
ammed with
ammed with
ammed with an
an
an
an
any
y
y
y
y QC code in type #1 with RP-200 selected "Y" f
QC code in type #1 with RP-200 selected "Y" f
QC code in type #1 with RP-200 selected "Y" f
QC code in type #1 with RP-200 selected "Y" f
QC code in type #1 with RP-200 selected "Y" for
or
or
or
or T
T
T
T
Tr
rr
rrunnking Contr
unnking Contr
unnking Contr
unnking Contr
unnking Control
ol
ol
ol
ol
IMPORTANT:
Ritron RRX Repeaters are best when using the shortest (20 mSec) firmware versions "lead-in delay," but can
use any Trident firmware. Specify "Ritron RRX" when ordering Controllers. Each brand of RF equipment is
unique to its own system installation. These jumper and switch indications are meant to be used as initial
settings. Adjustments to these settings may be required, depending on your system configuration.
