qtm9322b.pm5
For assistance, call RITRON at 800-USA-1-USA (800-872-1872) or visit us at www.ritron.com
C. TO PROGRAM THE ASSISTANCE NEEDED MESSAGE:
1. Pick up the telephone receiver and listen for the acknowl-
edge tone.
2. Dial
312
. Quick Assist responds with three short tones
to prompt you to begin speaking, then records the
message. This message is to be no longer than 8
seconds.
Remember: speak loudly and clearly.
EXAMPLE
:
Customer needs assistance in Aisle 9.
3. When you have finished speaking, press and release the
telephone flash-hook.
4. You may either continue programming additional
features, or you may dial
999
and hang up the tele-
phone to stop programming.
NOTE:
To review your recorded message,
dial "
412
".
D. TO PROGRAM TIME BETWEEN REPEATED MESSAGES:
(DEFAULT SETTING IS 30 SECONDS)
1. Look up the code for the desired time between mes-
sages on Table 4, below.
2. Pick up the telephone receiver and listen for the acknowl-
edge tone.
3. Dial
512
, then the code digit from Table 4.
EXAMPLE
:
If you select 2 minutes as the time between
messages, dial
5124
.
4. Quick Assist responds with a single beep to indicate it
has programmed the time between messages.
5. You may either continue programming additional
features, or you may dial
999
and hang up the tele-
phone to stop programming.
! ! ! IMPORTANT ! ! !
If your Quick Assist unit fails to operate
correctly, or is programmed incorrectly, put
the unit into default Quick Assist mode using
the following procedure:
1. Pick up the telephone receiver and listen for the
acknowledge tone.
2. Dial the correct option (A or B below), to restore
factory defaults; a short beep indicates successful
completion.
A. For RQT-150-PB, dial 978.
B. For RQT-450-PB, dial 979.
3. Dial 814 to put the unit into Quick Assist mode; a
short beep indicates successful completion.
4. Program Sections A through F, above. Section G is
optional.
5. Programming of the Ritron Quick Assist is complete!
E. TO PROGRAM THE ASSISTANCE IS NO
LONGER NEEDED MESSAGE:
1. Pick up the telephone receiver and listen for the acknowl-
edge tone.
2. Dial
311
. Quick Assist responds with three short tones
to prompt you to begin speaking, then records the
message. This message is to be no longer than 8
seconds.
EXAMPLE
:
Aisle 9 OK.
3. When you have finished speaking, press and release the
telephone flash-hook.
4. You may either continue programming additional
features, or you may dial
999
and hang up the tele-
phone to stop programming.
NOTE:
To review your recorded message,
press "
41
F. TO PROGRAM THE "LOW BATTERY" MESSAGE:
1. Pick up the telephone receiver and listen for the acknowl-
edge tone.
2. Dial "
35
". Quick Assist responds with three short tones to
prompt you to begin speaking, then records the message.
This message is to be no longer than 1.5 seconds.
EXAMPLE
:
"Low battery Aisle 9"
3. When you have finished speaking, press and release the
telephone flash-hook.
4. You may either continue programming additional features,
or you may dial
999
and hang up the telephone to stop
programming.
NOTE:
To review your recorded message,
dial "
45
".
G. TO PROGRAM THE "ASSISTANCE NEEDED" MESSAGE
REPEAT LIMIT: (DEFAULT SETTING IS 8 TIMES)
1. Look up the code for the desired number of message
repeats on Table 5, below.
2. Pick up the telephone receiver and listen for the acknowl-
edge tone.
3. Dial "
612
", then the code digit from Table 5.
EXAMPLE
:
If you select 3 times as the message repeat limit,
dial
6123
.
4. Quick Assist responds with a single beep to indicate it has
programmed the message repeat limit.
5. Dial
999
and hang up the telephone to stop program-
ming.
TABLE 5:
MESSAGE
REPEAT LIMIT
CODE NUMBER
1 time ...................................................... 1
2 times ..................................................... 2
3 times ..................................................... 3
4 times ..................................................... 4
5 times ..................................................... 5
6 times ..................................................... 6
7 times ..................................................... 7
8 times ..................................................... 8
Repeat forever; no limit ............................. 9
DEFAULT
(Programming Instructions continued from page 2)
4
TABLE 4:
TIME BETWEEN
MESSAGES
CODE NUMBER
No Message ............................................. 0
On Changes Only ..................................... 1
30 seconds .............................................. 2
1 minute ................................................... 3
2 minutes ................................................. 4
5 minutes ................................................. 5
10 minutes ............................................... 6
30 minutes ............................................... 7
1 hour ...................................................... 8
2 hours .................................................... 9
DEFAULT
