Ritchie CattleMaster CM10T Installation Instructions Manual Download Page 2

CattleMaster Series 

Installation Instructions

 

A.

Location  - 

Installing  the  fountain  in  a  location  that  offers  protection  from  the  wind  will  enhance  the

performance  of  the  fountain.  Livestock  will  tend  to  gather  in  this  protected  area,  enticing  them  to  drink  more. 

Access panel should be opposite of prevailing winter wind to give additional protection to the supply line.

  

B.

Water  Supply  Line

  -  Horizontal  underground  water  line  should  be  sized  to  account  for  pressure  drop,

relating  to  distance,  and  placed  one  foot  below  frost  line.  A  one-inch  vertical  supply  pipe  is  recommended.  A 

shut-off valve should be installed under fountain to allow for easier servicing. For optimum serviceability, a stop 

and waste valve can be installed below frost level to drain water when unit is not in use. Vertical supply line must 

be centered in riser tube to provide an air space between the line and frozen ground outside of tube. Flush water 

supply line thoroughly before connection to fountain. Water supplies with foreign material such as sand, rust, etc. 

may require a filter to keep fountain valve working properly. 

C.

Electric Supply 

– It is generally most cost effective to run your electrical supply line at the same time you are

trenching for your water supply. 

WARNING:  ANY  ELECTRICAL  SERVICE  MUST  BE  INSTALLED  AND 

MAINTAINED BY A QUALIFIED ELECTRICIAN.

 

D.

Riser Tube

 - Install a riser tube and extend it at least one foot below frost line

or down to horizontal underground water line. For optimum water line 

protection, use 

the 12” diameter insulated Ritchie 

Thermal Tube, part numbers and sizes are shown 

to the right. Tube opening must be kept clear.  

NOTE: 

The supply line touching the riser tube is the most common cause of the supply line freezing. 

Do not surround the supply line with insulation, wood, or other foreign material. Any foreign material in 

the tube may cause frost to migrate to the supply line causing it to freeze.

 

Ritchie Thermal Tube 

Part # 

Description 

18158 

1’ Top Section 

16417 

2’ Top Section 

16612 

4’ Top Section 

16416 

2’ Extension 

SHUTOFF VALVE

WATER SUPPLY

ELECTRICAL SERVICE
PER LOCAL CODE

ANCHOR BOLT

STANDARD DRAIN

UNDERGROUND DRAIN
OPTIONAL

CONCRETE

RISER TUBE

FROST LINE

CattleMaster Series Instruction Manual

1

January 1, 2020

Summary of Contents for CattleMaster CM10T















Reviews: