background image

5

FLIGHT MODES

The RXS270 has three flight modes.

Stability Mode

 has limits on the tilt angle and the quadcopter will level itself 

in this mode when the right stick is centered.

FPV Mode

 will not level the quad and has no limits to tilt angles. The quadcopter 

will be more maneuverable and the flight will be smoother in this mode.

Acro Mode

 is available for experienced pilots that want maximum maneuverability 

while performing acrobatics. The quadcopter will react faster in this mode than 
in the FPV mode.

SETUP

All the bolts have been tightened to the proper torque and have thread locking 

compound applied to keep them secure.

PROP ADAPTER INSTALLATION

The silver prop adapters should be 

installed on the front left and rear 
right motors. The black prop 
adapters should be installed on the 
front right and rear left motors. 
Please use a threadlocking 

compound on the screws.

RECEIVER MOUNTING

Attach the receiver to the rear center 

plate of the frame with double sided 
tape. Route the antenna wires into 
the folding antenna tubes.

FRONT

Silver Prop

Adapter

Black Prop

Adapter

Silver Prop

Adapter

Black Prop

Adapter

Receiver

Summary of Contents for RXS270

















Reviews: