background image

2

INTRODUCTION

Thank you for purchasing the VUSION FPV RACER. We want the time you spend 

with your new R/C quadcopter to be fun and successful so please read the entire 

manual before beginning setup. If for any reason you think this R/C model is not 
for you, return it to the dealer immediately. Your dealer cannot accept returns on 
any model after final assembly.

For the latest technical updates or manual corrections for the VUSION FPV RACER 
please visit the Rise web site at www.explore-rise.com . If there is any new technical 
information, changes or important updates to this model, a “tech notice” box will 
appear on the page. Click the “tech notice” box to learn more.

SAFETY PRECAUTIONS

Failure to follow these safety precautions 
may result in injury to yourself and others.

  Keep your face and body as well as all spectators away from the rotating plane 

of the blades whenever the battery is connected. Keep loose clothing, shirt 
sleeves, ties, scarfs, long hair or loose objects such as pencils or screwdrivers 
that may fall out of shirt or jacket pockets away from the rotors. The spinning 
blades of a model quadcopter can cause serious injury. When choosing a 
flying site for your VUSION FPV RACER, stay clear of buildings, trees and power 
lines. 

AVOID

 flying in or near crowded areas. 

DO NOT

 fly close to people or 

pets. Maintain a safe distance from the quadcopter.

  Your VUSION FPV RACER should not be considered a toy. Because of its 

performance capabilities, the VUSION FPV RACER, if not operated correctly, 
could cause injury to you or spectators and damage to property.

  

DO NOT

 alter or modify the model. Doing so may result in an unsafe or unflyable 

model.

  When and if repairs are necessary you must correctly install all components so 

that the model operates properly on the ground and in the air. Please check 
the operation of the model before every fl ight to insure that all equipment is 
operating and that the model has remained structurally sound. Be sure to check 
connectors and the propellers before each fl ight. Replace them if they show 
any signs of wear or fatigue.

KNOW BEFORE YOU FLY

As a new owner of an unmanned aircraft system (UAS), you are responsible for 

the operation of this vehicle and the safety of those around you. Please contact 

your local authorities to find out the latest rules and regulations.

knowbeforeyoufly.org

faa.gov/uas

Summary of Contents for FPV RACER

















Reviews: