RioOutdoors 6F-SC Installation Instructions Manual Download Page 5 | Manualshive

Page: 5 / 25

RioOutdoors 6F-SC Installation Instructions Manual Download Page 5

5 |

P a g e

1.3

CONTENTS OF KIT # 6F-SC

The contents of this kit are shown in the table, below. Before you begin your project, take an inventory of all items that you

received from us. If any items are missing, contact us directly via email at

[email protected]

. Include your name and

shipping address and your order number, if available. We will respond within 24 hours with a resolution to your problem.

Item SKU #, Description

Item Qty

Item Image

6x6 Post-Top/Floor 2-way Elbow Bracket

SKU# 6C2L

8

¼ x 1-1/4” Lag Screw

80

1.4

OPTIONAL DECK SUPPORT BEAM BRACKETS

If you wish to build a wooden deck as the floor for your floating pergola, you may wish to use our deck beam support brackets,

SKU #24BS. This bracket can support 2x4 or 2x6 beams. You can order the required number of brackets at RioOutdoors.com.

Deck Beam Support Brackets (Qty 2 every 24”)

RioOutdoors.com SKU# 24BS

6 for 8 ft.

8 for 10 ft.

10 for 12 ft.

«
...
3
4
5
6
7
...
»

Summary of Contents for 6F-SC


























Reviews:

No comments