Rinstrum D841 Installation Manual Download Page 2

D841/D850 Installation Manual 

 

Page 2 

 

008D-600-150 

1. 

Specifications 

 

Display 

 

Display

 

D841 

–  Full  LED  Dot  Matrix  with  up  to  seven  (7)  full  alpha 

numeric  characters  with  decimal  point  at  120  degrees  viewing 
angle. 

  Character size (H x W) 

– 100mmx60mm (4"x2.4") 

  14 x 64 LED matrix at 14 x 8 LEDs per character 

  Status annunciators for Motion, Centre of Zero and Net 

  kg, lb, t, and g units 

  50mm (2") round RED and GREEN traffic lights 

D850 

–  Full  LED  Dot  Matrix  with  up  to  seven  (7)  full  alpha 

numeric  characters  with  decimal  point  at  120  degrees  viewing 
angle. 

  Character size (H x W) 

– 140mmx80mm (5.5"x3.2") 

  14 x 64 LED matrix at 14 x 8 LEDs per character 

  Status annunciators for Motion, Centre of Zero and Net 

  kg, lb, t, and g units 

Performance 

 

Visibility 

D841 

– Greater than 30m (100 feet) at 120 degrees viewing angle 

D850 

– Greater than 70m (230 feet) at 120 degrees viewing angle 

Update Rate 

Dependent on data update rate 

Operating 
Environment 

Temperature: 

–20 to +60

C, -4 to 140

F case temperature 

Humidity:<90% RH non-condensing 
Storage: 

–20 to +60

C, -4 to 140

F ambient 

Digital 

 

Setup 

Automatic detection with adjustment via a command string 

Memory 

Full non-volatile operation 

Dimensions 

 

External 
Dimensions 
L x H x D 

D841 

– 760mm x 150mm x 80mm (30" x 6" x 3.2") 

D850 

– 799mm x 200mm x 80mm (31.5" x 8" x 3.2") 

Display Window 
L x H 

D841 

– 515mmx115mm (20.3"x4.5") 

D850 

– 644mmx135mm (25.4"x5.3") 

Weight 

D841 - 4.6 kg (10.2 lb) 
D850 - 6 kg (13.2 lb) 

Power  

 

AC Power 

110-240VAC 50/60Hz 32W MAX 

DC Power (option) 

24VDC (18

–36VDC) or 12VDC (9–18 VDC) 30W MAX 

Features 

 

Data Inputs 

RS-232 

– two wire, receive only 

RS-485 

– two wire, receive only 

Ethernet (Optional) 

Baud Rate 

Auto detect Baud 2400 to 19200, Parity and Bit detection 

Unit Addressing 

Up to 100 addresses supported (00-99) 

Display Timeout 

5 seconds on data loss (default), adjustable 

Protocol Selection 

Auto detection, Locking with configuration string 

Summary of Contents for D841


















Reviews: