Rinnai Maxim X4S Operating And Assembly Instructions Manual Download Page 5

S

A

F

E

T

Y

5

5

NEVER CHECK FOR LEAKS WITH 
A FLAME

!

IF YOU HAVE A GAS LEAK YOU 
CANNOT RECTIFY, TURN OFF THE GAS
AT THE SOURCE.  CONTACT THE 
MANUFACTURER 

!

ALWAYS CHECK FOR GAS LEAKS 
EACH TIME YOU USE YOUR BARBECUE

!

1.

Make liquid detergent solution by mixing one (1)
part liquid detergent and four (4) parts water.

2.

Turn burner control(s) to 

‘OFF’

, then turn on gas at

source.

CHECKING FOR GAS LEAKS

You should follow this procedure after any of the following:

• Not having used the barbecue for an extended period of time,
• Initial assembly of barbecue,
• Any disconnection and reconnection of hose assembly,
• Changing gas cylinder,
• Upon re-connecting gas cylinder after it has been disconnected for storage.

4 parts water

Open

1 part liquid

detergent

3.

NOTE: Although hoses are factory fitted, it is
advisable to leak test before using your barbecue.

Apply the liquid detergent solution to all visible and
accessible gas connections, including the connection to
the gas cylinder.  Bubbles will appear in the liquid deter-
gent solution if connections are not properly sealed.
Tighten or rectify as necessary. 

Summary of Contents for Maxim X4S

























Reviews: