background image

- 14 - 

OPERATION WITH STANDARD TEMPERATURE CONTROLLERS

  

To TURN OFF your hot water system 

 
 

Simply press the ON/OFF button on any 
Temperature Controller (where fitted). This will 
shut the Infinity down completely including the 
Temperature Controller digital displays. 
 
The ON indicator will go out. 
 
If hot water taps are opened when the Infinity is 
OFF, cold water will flow from the taps. 

 

 
 
 
 
 

Additional SAFETY features 

 
 
Whilst the hot water tap is open, the following 
safety features apply. 
 

Temperature selection cannot be transferred. 

 

Water temperature can only be adjusted between 
37

°

C and 43

°

C. 

 

The Kitchen and Bathroom Control cannot be 
turned ON. 

 
 
 
 

 

 
 
 
 

 

 

 

 
 
 

 
 
 

O N / O F

F

ON

The temperature of outgoing hot water is constantly monitored by a built-in sensor. If the 
temperature of the outgoing hot water rises to more than 3

°

C above the selected temperature 

shown on the Digital Monitor or the pre-set limit when Temperature Controllers are not fitted, 
the burner will automatically go out. The red operation indicator will also go out. The burner 
will ignite again once the outgoing hot water temperature falls to that shown on the Digital 
Monitor (or the pre-set limit).

NOTE

Summary of Contents for infinity 18































Reviews: