Rinnai ByPass Servo Troubleshooting Manual Download Page 31 | Manualshive

Page: 31 / 43

background image

31

11112014GW

Code 65 Troubleshooting Procedure

Water Flow Servo

1.

Check wiring harness to the water flow servo for loose, broken or damaged connections from
servo back to PC board.

2.

Turn off the power to the water heater and then reapply to see if code resets.

3.

The water flow servo valve has failed to close during the bath fill function. Immediately turn off
the water flow and discontinue the bath fill function.

4.

WARNING:

Turn off the electrical, gas and water supply to the water heater before proceeding.

Replace water flow control servo.

If the water flow servo motor is disconnected when the unit tries to cycle the product will post a
code 65. This will shut the unit down until the WFSV motor is plugged back in and the power is
turned off and then on again.

«
...
29
30
31
32
33
...
»

Summary of Contents for ByPass Servo












































Reviews:

No comments

Related manuals for ByPass Servo

Brand: DAB Pages: 8

Brand: Harry Taylor Pages: 56

Brand: Vanguard Pages: 14

Brand: Harry Taylor Pages: 52

Brand: Navien Pages: 60

Brand: veito Pages: 28

Brand: Wangen Pages: 72

Odyssey ODYR-25-1

Brand: Dakota Digital Pages: 8

Brand: Zehnder Pumpen Pages: 32

Altherma EKHWE150A3V3

Brand: Daikin Pages: 10

Brand: EBARA Pages: 48

Wilden A2550V Series

Brand: PSG Pages: 16

Brand: Watts Pages: 22

Brand: Graco Pages: 32

MUNA E T - MOUNTING

Brand: RADSON Pages: 8

Brand: Opal Pages: 38

Brand: Barmesa Pumps Pages: 15

Brand: Ningbo Innopower Hengda Metal Products Pages: 21

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands