Rinnai BC-100V1Z Operation And Installation Manual Download Page 13

Rinnai INFINITY Deluxe controller OIM 01-20 |  

13 

 

Water controller installation

General information

Other manufacturers water controllers are NOT compatible with Rinnai water heaters. Water 

controllers MUST NOT be used with any solar boost water heater, or N-Series ring main 

applications.

Rinnai water controllers bought in from other countries are not compatible with Rinnai appliances 

sold in New Zealand.

Controller configurations

Refer p. 5.

Controller location

• 

Do not install water controllers near a heat source, such as a cook top, stove or oven—heat, 

steam, smoke, and hot oil may cause damage 

•  Do not install water controllers outdoors unless protection from water/dust ingress and sunlight 

are provided 

•  The Kitchen Deluxe (MC-100V1Z) controller MUST NOT be installed in a bathroom 

•  Do not install water controllers in direct sunlight 

•  Do not install water controllers against a metal wall unless the wall is earthed in accordance 

with AS/NZS 3000 

•  Water controllers must not be installed where chemicals such as benzene, alcohol, turpentine, 

hydrogen sulphide, ammonia, chlorine or similar chemicals are in use

The water controller is water resistant, however excessive exposure to water may result in 

damage. Durability is improved when positioned OUTSIDE the shower recess.

•  Avoid direct exposure to water or steam as these may cause the controller to malfunction 

• 

Water controllers must be installed in shaded clean locations. They should be fitted out of reach 

of children (recommended height 1.5 m from the floor), and installed at least 400 mm above the 

highest part of a sink, basin or bath.

The deluxe controllers use a liquid crystal display (LCD) for the digital monitor. 

Light reflection can make the LCD difficult to see at direct eye level. For best 

results mount the controller lower than eye level.

Communication cables

Controllers operate at an extra low voltage (12 V DC), which is supplied from the water heater. A 

10 m communication cable is supplied for connection to the water heater. ONLY Rinnai supplied 

communication cables may be used. Additional 10 m cable can be purchased.

Additional 10 m cable codes:

•  Kitchen Deluxe   

R1369

•  Bathroom Deluxe   

R1069

Summary of Contents for BC-100V1Z





















Reviews: