Rigol DL3000 Series User Manual Download Page 127

Page: 127 / 163

Chapter 2 Front Panel Operations

RIGOL

DL3000 User’s Guide

2-97

Communication Interface Setting

Press Utility to enter the system utility function interface, and then press Interface

to enter the interface tab. By default, "GPIB" is selected, as shown in Figure 2-53.

Figure 2-53 "GPIB" Tab Interface

The load supports GPIB (extended from the USB-GPIB interface converter), USB,

RS232, and LAN. Remote control can be realized via these interfaces. When you

select GPIB, RS232, or LAN, please set the parameters for the interface first.

Set the GPIB address

Before using the GPIB interface, use the USB-GPIB interface converter to extend the

GPIB interface, and then use the GPIB cable to connect the load to the PC.

Procedures for setting the GPIB address are as follows:

(1)

Press Interface to enter the communication interface tab. By default, "GPIB" is

selected and it is highlighted.

(2)

Use the numeric keys to set the GPIB address.

(3)

Press OK to confirm it.

The GPIB address is an integer ranging from 0 to 30. By default, it is 2. The setting is

stored in the non-volatile memory, which will not be affected even if you restore the

load to its factory defaults.

Tip



When the load is connected to power source, you can also connect/disconnect

USB and LAN interfaces.



GPIB, USB, RS232, and LAN interfaces cannot be used synchronously. Each

time, only one type of interface can be used.

Summary of Contents for DL3000 Series




































































































































































Search results

Summary of Contents for DL3000 Series

Reviews:

Related manuals for DL3000 Series

Brands by name

Popular brands

Rigol DL3000 Series, User Manual

Search results

Summary of Contents for DL3000 Series

Reviews:

Related manuals for DL3000 Series

Brands by name

Popular brands