Wiz
BLOOD GLUCOSE TEST STRIP INSERT
Test Result
- Blood glucose test results are shown on the meter as mg/dL or mmol/L, depending on the preset of
your meter.
- If your blood glucose result is unusually high or low, or if you question your results, repeat the test with
a new test strip. You can also run a Quality Control Test with RIGHTEST Wiz Control Solution to check
your meter and test strip. If the test result still remains unusually high or low, contact your healthcare
professional immediately.
- If you are experiencing symptoms that are not consistent with your blood glucose test results and you
have followed all the instructions in this manual, contact your healthcare professional immediately.
- RIGHTEST Meter displays results between 10 to 600 mg/dL or 0.6 to 33.3 mmol/L. If your test result is
below 10 mg/dL (0.6 mmol/L) , " Lo " will appear on the screen. Please repeat your test with a new
strip. If you still get a " Lo " result, you should immediately contact your healthcare professional.
- If your test result is above 600 mg/dL (33.3 mmol/L), " Hi " will appear on the screen. Please repeat
your test with a new strip. If you still get a " Hi " result, you should contact your healthcare professional
immediately.
Limitations
- The meter readings of the blood glucose may be significantly lower than " true glucose levels " in the
hyperglycemic-hyperosmolar state, with or without ketosis. Critically ill patients should not be tested by
the RIGHTEST System, or tested with extreme caution.
- Caution is advised in the interpretation of glucose values below 50 mg/dL (2.8 mmol/L) or above 250
mg/dL (13.9 mmol/L). Consult a physician as soon as possible, if values in this range are obtained.
- Healthcare professionals should evaluate their technique and their patients' technique at periodic
intervals. To accomplish this, it is recommended to compare the meter result with a laboratory result
using the same blood sample. A well characterized clinical laboratory method employing hexokinase
or glucose oxidase should be used as the comparative method.
Precautions
- Check the expiration date printed on the strip vial. Do not use expired test strips.
- Close the vial cap immediately after taking test strip out from the vial.
- Do not perform quality control test with expired control solution.
- Do not bend or twist the test strip. Damage of test strip may cause wrong result.
- Do not reuse test strips and lancets.
- Discard the used disposable lancet and strip into an appropriate puncture-proof or biohazard container.
-
If RIGHTEST Meter or Test Strips are exposed to temperature environments out of operating
range– below 10°C (50°F) or above 40°C (104°F)– please wait 30 minutes before testing again.
- If you want to purchase new control solutions, please contact your authorized Bionime representative.
8) To remove the lancet, pull off the depth adjustable cap of
lancing device. Without touching the used disposable lancet,
stick the lancet tip into the protective cover. Hold the release
button of lancing device in one hand and pull on the plunger
in the other hand will safely eject the used disposable lancet
into an appropriate puncture-proof or biohazard container.
Warning
- Keep the test strips or vial cap away from children. They may cause a choking hazard. If a test strip or
vial cap is swallowed, contact your physician immediately.
For more information on how to use your meter,
lancing device and understand your test results,
see the User’s Manual.
6) You will see the countdown mode on the screen. After 5 seconds, the test result appears.
7) Remove the test strip from the meter. Please follow the local regulation and discard the used strip
properly.
6
7
(1)
Expected values
GLUCOSE LEVEL
From 70 to 99 mg/dL (3.9 to 5.5 mmol/L)
From 100 to 125 mg/dL (5.6 to 6.9 mmol/L)
126 mg/dL (7.0 mmol/L) and above on more than one testing occasion
INDICATION
Normal fasting glucose
Pre-diabetes (Impaired fasting glucose)
Diabetes
Fasting Blood Glucose
0.75
1.0
3
μ
L
μ
L 1.5
μ
L 2.0
μ
L .0
μ
L
Please take a minimum of 0.75
μ
L to do the test on
glucose monitoring system. Blood sample size
above 3.0
μ
L might contaminate the meter.
Sample Size Example
Alternative site testing-palm or forearm blood sampling
- To perform a test using samples obtained from alternative sites,
install the
clear cap on the lancing device (For more information on how to install, see
the Instructions for the lancing device).
- To increase the blood flow, massage the puncture area of palm or forearm
for a few seconds.
-
Immediately after massaging the puncture area, press and hold the lancing
device with the clear cap against palm or forearm.
- Then press the release button.
- Continue holding the lancing device against palm or forearm and gradually
increase pressure for a few seconds until the blood sample size is sufficient
(Refer to Instructions for the lancing device).
Releasing
button
Pressing for
a few seconds
Intended Use
RIGHTEST Wiz and Wiz Plus Blood Glucose Monitoring Systems are used by individuals with diabetes.
It's for checking on glucose levels of whole blood from capillary. Capillary blood can be sampled from
the fingertip, palm and forearm. It's as an aid in management of diabetes at home and clinical sites.
RIGHTEST Wiz Blood Glucose Test Strips were designed for self-testing outside the body (
in vitro
diagnostic use).
The RIGHTEST Blood Glucose Monitoring System aids to diabetes control, could be used by healthcare
professionals in clinical setting, also by people to use at home.
RIGHTEST System tests the capillary whole blood and provides results equivalent to plasma result in
laboratory test.
RIGHTEST Wiz Blood Glucose Test Strip is designed for use with RIGHTEST Wiz / Wiz Plus Blood
Glucose Meter to obtain accurate results.
Performing a Test
1
1) Take one test strip from the vial. Re-cap the vial cap
immediately.
2) Insert the test strip into the test strip port of the meter with
the indication symbol facing up.
3) While the blood drop symbol is flashing, you are ready to
apply the blood sample within 2 minutes.
4) Place the lancing device against the pad of your fingertip and press the release button.
5) Touch and hold the drop to the edge of sample entry until you hear a " beep " (if volume is turned on)
and the View Window is totally filled with blood. If the View Window is not totally filled with blood or
the test does not start, please discard the test strip and repeat the test with a new test strip.
2
4
Preparing the Lancing Device
Wash your hands with warm soapy water and dry thoroughly before you start the test.
1)
Hold the depth adjustable cap in one hand and hold the hub in the other hand. Bend the cap towards
the down side, until a gap appears between the cap and hub.
2)
Pull the cap and hub off in opposite directions, remove the cap.
3) Insert a new disposable lancet firmly into lancet carrier.
4) Twist off and set aside the protective cover of the disposable lancet.
5) Replace the depth adjustable cap.
6)
The adjustable cap with 7 depth levels allows you to select the depth of penetration by rotating the
cap until the preferable depth display in the window. Settings are based on skin type for soft or
"
"
thin skin; for average skin; for thick or calloused skin.
"
"
"
"
7) Hold the hub in one hand and pull on the plunger in the other hand. The device will be cocked. Release
the plunger, it will automatically move back to its original position near the hub.
Test Procedure
3
5
7
6
5
4
3
2
1
Palm
Forearm
