DETAIL A
PRE-INSTALLED
T-SLOT PLATE
6703 ZINSER ST., SCHOFIELD, WI 54476
PHONE: 800.298.4351 FAX: 866.882.9475
www.raproducts.com
K&A MANUFACTURING
MOTOR
STEPS 1-5
8
WIRES
SUPPORT
2
3
1
4
7
5
6
HARDWARE PACK # 52226
WORKSURFACE
FOOT
HARDWARE QUANTITIES MAY VARY
LEVEL
AND THE RIGHT HAND
COLUMN ASSEMBLY
3
STEP 3:
ON THE WORKSURFACE
1
AS SHOWN. THE MOTOR
WIRES MUST FACE THE INSIDE OF THE WORKSTATION. ALIGN THE HOLES IN THE
WORKSURFACE SUPPORTS WITH THE PILOT HOLES IN THE WORKSURFACE.
TOOLS REQUIRED FOR ASSEMBLY:
#2 SQUARE HEAD DRIVER BIT
INSTRUCTION # 52598
4mm HEX HEAD DRIVER BIT OR
ALLEN WRENCH PROVIDED
TAPE MEASURE
TIGHTEN THE SCREWS. USE A LOW TORQUE SETTING ON THE DRILL.
PAGE 1 OF 3
CORDLESS DRILL
. DO NOT OVER-
#2 PHILLIPS HEAD DRIVER BIT OR
8
WITH THE HELP OF AN ASSISTANT, PLACE (4) STAR WASHERS
5
TO THE WORKSURFACE USING (16) WOOD SCREWS
ON (4)
SOCKET SCREWS
6
. INSERT THESE THROUGH THE HOLES AT THE ENDS OF THE
CROSS SUPPORT
. ATTACH THE WORKSURFACE SUPPORTS
4
AND THREAD THEM INTO THE T-SLOT PLATES THAT ARE PRE-
INSTALLED IN THE SLOTS IN THE COLUMN ASSEMBLIES
2
1
AND
3
THE CROSS SUPPORT.
. SEE DETAIL A
AT LEFT. DO NOT FULLY TIGHTEN.
HOLES IN THE WORKSURFACE
STEP 4:
ALIGN THE HOLES IN THE WORKSURFACE SUPPORTS WITH THE PILOT
LEVEL THE CROSS SUPPORT
4
AT 4" FROM THE BOTTOM OF THE WORK-
SURFACE SUPPORT AND FULLY TIGHTEN THE SOCKET SCREWS
INTO THE ENDS OF
6
. SEE THE
STEP 5:
DETAIL AT LEFT.
SPECIAL EXCEPTION: ON WORKSTATIONS ON WHICH THE
LifeBalance STATION IS BEING INSTALLED, THE CROSS SUPPORT SHOULD BE
INSTALLED RESTING ON THE FEET OF THE COLUMN ASSEMBLIES TO ALLOW FOR
CLEARANCE OF THE EQUIPMENT.
INSERT (2) END CAPS
7
NewHeights SPLIT WORKSURFACE ELECTRIC HEIGHT ADJUSTABLE WORKSTATION
ASSEMBLY INSTRUCTIONS:
STEP 1:
LAY THE FIXED WORKSURFACE
1
ON A PROTECTED SURFACE WITH
THE PILOT HOLES FACING UP.
STEP 2:
PLACE THE LEFT HAND COLUMN ASSEMBLY
2
ITEM # PART #
DESCRIPTION
QTY.
1
VARIES NewHeights FIXED WORKSURFACE
1
2
VARIES NewHeights LEFT HAND COLUMN ASSEMBLY
1
3
VARIES NewHeights RIGHT HAND COLUMN ASSEMBLY
1
4
VARIES NewHeights CROSS SUPPORT
1
5
52477 3/8 INTERIOR TOOTH STAR WASHER
4
6
52470 3/8-16 x 3/8 BUTTON HEAD SOCKET SCREW
4
7
800411 NewHeights/HOVER END CAP
2
8
51708 M5 x 18mm SQ/PH/WSHR HEAD WOOD SCREW
19
9
VARIES NewHeights MOVABLE WORKSURFACE
1
10
50219 NewHeights SWING ARM (300SW)
1
11
50072 8 x 3/4 PHILLIPS PAN HEAD RECEX DRIVE SCREW
4
12
51951 WIRE MANAGEMENT J
3
13
50298 NewHeights CONTROL BOX
1
14
50285 NewHeights HAND SWITCH
1
15
52498 7/32" ALLEN WRENCH
1
VERSION DATED: 7/18/12
LOCATING THE CROSS SUPPORT
(SEE EXCEPTION IN STEP 4)
BOTTOM OF
WORKSURFACE
SUPPORT
4.00
