6.3 Pull out isolators located between contacts + and battery holders
first from the backup power supply battery, and after from the main one.
In case of external power supply apply 12 V on the Detector terminals.
6.4 LED indicator blinking green displays the Detector readiness for
the binding procedure.
6.5 In case the LED indicator does not blink, close the «RESET»
contacts (5) for 2–3 s.
6.6 After a successful binding with the CP, the LED indicator lights
red for 2 - 3 s.
6.7 The «Binding» procedure is limited to 100 sec. After it expires, the
Detector changes to the sleep mode. To resume the «Binding» mode,
the «RESET» contacts (5) must be closed for 2–3 с.
7 Choosing Place of Installation
7.1 It is not recommended to install the annunciator at the following
places:
- directly on metal constructions and closer than 1 m to them;
- closer than 1 m to electrical power cables, as well as metal water
& gas pipes;
- adjacent to radio-interference sources;
- inside metal construction.
7.2 Annunciator power supply cables should be located far enough
from electrical power cables.
7.3 Install the annunciator in the place, where communication quality
is appraised as «good» or «excellent» (see Cl. 8).
8 Communication Quality Appraising
8.1 Bring the annunciator to the chosen place of installation.
8.2 Push «TEST» button for a second.
8.3 Appraise communication quality of the annunciator and the CP
as per LED indication (See Table 4).
Table 4 – Communication quality appraisal LED indication
LED Indication
Communication
Quality Appraisal
Recommendations
Color
Mode
Green
Three blinks
Excellent
Install the annunciator at
this place
Green
Two blinks
Good
Green
One blink
Communication
established
Choose another place
of installation or use a
repeater***
Red
Blinks series
No communication
***) — «Ladoga-RK» system repeater
9 Mounting
9.1 Choose place of installation of the annunciator, mark places for
it’s mounting. Use the annunciator case for marking. (See Figure 1).
9.2 Fasten case to the wall by two screws.
9.3 Check the PCB fixation in holders (See Figure 1).
10 Storage and Transportation
10.1 The annunciator are transported without power supply battery.
The annunciator in their original packaging are resistant to:
- transport jolting with the acceleration up to 30 m/sec
2
at impact
frequency range
from 10 to 120 per minute or 15 000 strikes;
- ambient temperature range minus 50 ... +50 °С;
- relative air humidity (95 ± 3) % at a tempe35 °С.
10.2 The annunciator in original package may be transported by
any means of transportation in closed vehicles over any distances in
compliance with the existing shipping rules concerning the respective
means of transportation.
10.3 After transportation under the conditions different to exploitation
conditions the annunciator shall be ready to operate after a maximum
of six hours.
10.4 The storage room shall be free from current-conducting
dust, acid vapors, alkali and gases that cause corrosion and destroy
insulation.
11 Manufacturer’s Guarantees
The manufacturer guarantees conformity of the annunciator to it’s
Technical Specifications provided that the transportation, storage,
installation and operation conditions are observed.
11.2 The guaranteed shelf life of the annunciator is 63 months since
the date of manufacture.
11.3 The guaranteed useful life is 60 months since the day of putting
into operation within the guaranteed shelf life.
11.4 The annunciators that are found non-conforming to the Technical
Specifications shall be repaired by the manufacturer, provided the
installation and operation rules have been complied with.
Note
– Warranty obligations are not applied to the power-supply
batteries.
12 Acceptance and Packing Certificate
Wireless light alarm annunciator «Trubach-T-RK»manufactured in
accordance with current technical documentation is classified as fit
for operation and is packed by «RIELTA» JSC.
Packing date _______________________________
month, year
Rev. 4 of 22.11.18
№00330
Axsem
v10.1
Made in Russia
«RIELTA» JSC, www.rielta.com,
Chapaeva Str. 17, Saint Petersburg, Russia, 197101, [email protected],
Tel./fax. +7 (812) 233-0302, 703-1360,
Technical support, tel. +7 (812) 233-29-53, 703-13-57, [email protected]
.
