9.4 Turn on the device manually from the accumulator by shorting
the START contacts with any conductive object until red and green
indicators are on (indication of start).
9.5 Push tamper contact and then close START contacts over again
until binding LED indication appears.
9.6 Fulfill binding. Successful binding is displayed by the red indicator
shot-term lighting.
Notes:
1. Frequent flashing (4 Hz) of green led indicates the binding mode.
2. The binding mode is active for 100 seconds. Repeat instructions
given in clause 9.5 to renew binding.
3. To exit from the binding mode reconnect the START contacts.
4. Don’t leave the CN-Repeater with closed contacts as it will lead to
full discharge and damage of the accumulator. The flashing of green
led (1 Hz) indicate that the START contacts are closed.
10 Choosing Place of Installation
10.1 It is not recommended to install the CN-Repeater in the following
places:
- on massive metal constructions and closer than 1 m from them;
- near source of radio interferences;
- inside metal constructions.
10.2 It is recommended to locate the CN-Repeater in such a position,
in which antenna has vertical orientation.
11 Communication Quality Appraising
11.1 Main power supply should be switched off to avid contact with
mains socket with dangerous voltage. Energize the CN-Repeater from
the storage battery by closing START contacts by current-conducting
item till green LED lighting up.
11.2 Carry the CN-Repeater binded in the CP to assumed place
of installation and locate it in such a position, in which antenna has
vertical orientation.
11.3 Press and hold the tamper contact for a few minutes.
11.4 Release tamper contact.
11.5 Appraise CN-Repeater communication quality with the CP by
LED indication (see Table 4).
Table 4 – LED indication of communication quality appraisal
LED Indication
Communication
Quality Appraisal
Recommendations
Color
Mode
Green
Three blinks
Excellent
Install the Detector at
this place
Green
Two blinks
Good
Green
One blink
Communication
established
Choose another place
for installation
Red
Four blinks
No communication
12 Storage and Transportation
12.1 The CN-Repeater are transported without power supply battery.
The CN-Repeater in their original packaging are resistant to:
- transport jolting with the acceleration up to 30 m/sec
2
at impact
frequency range
from 10 to 120 per minute or 15 000 strikes;
- ambient temperature range minus 50 ... +50 °С;
- relative air humidity (95 ± 3) % at a tempe35 °С.
12.2 The CN-Repeater in original package may be transported by
any means of transportation in closed vehicles over any distances in
compliance with the existing shipping rules concerning the respective
means of transportation.
12.3 After transportation under the conditions different to
exploitation conditions the CN-Repeater shall be ready to operate
after a maximum of six hours.
12.4 The storage room shall be free from current-conducting
dust, acid vapors, alkali and gases that cause corrosion and destroy
insulation.
12.5 The battery must be charged during storage. The battery must
be removed from the holder or an insulator must be installed between
the "+" contact of the battery and the holder.
13 Manufacturer's Guarantees
13.1 «RIELTA»
JSC guarantees conformity of the CN-Repeater to
the requirements of technical conditions provided the transportation,
storage, installation and operation conditions are observed.
13.2 The guaranteed shelf life of the CN-Repeater is 63 months since
the date of manufacture.
13.3 The guaranteed useful life is 60 months since the day of putting
into operation.
13.4 The CN-Repeater that are found non-conforming to the
requirements of technical conditions shall be repaired by the
manufacturer, provided the installation and operation rules have been
complied.
13.5
For warranty service contact address:
Research and technology business company «C.Nord» LLC
199 – 201, Obvodny Canal Embankment, Saint-Petersburg, Russia,
190020
Tel: +7 (812) 327-16-36
E-mail: [email protected], [email protected]
www.cnord.ru
Note
– Warranty obligations are not applied to power supply battery.
Rev. 4 от 12.09.19
v.10.1
Made in Russia
By order of: Research and technology business company «C.Nord» LLC
199 – 201, Obvodny Canal Embankment, Saint-Petersburg, Russia,190020
Tel: +7 (812) 327-16-36
E-mail: [email protected], [email protected]
www.cnord.ru
The Manufacturer:
«RIELTA»
JSC
17, Chapaeva str., Saint-Petersburg, Russia,197101
Tel /fax: +7 (812) 233-03-02, 703-13-60
Technical support: Tel +7 (812) 233-29-53, 703-13-57
E-mail: [email protected], [email protected]
www.rielta.com
