background image

20052068

12 

GB

Technical description of the burner

3.9

Control box for the air/fuel ratio (LMV37.4...)

Warning notes

All  activities  (mounting,  installation  and  service  work,  etc.)
must be performed by qualified staff.

Before  making  any  wiring  changes  in  the  connection  area,
completely  isolate  the  plant  from  mains  supply  (all-polar  dis-
connection).  Ensure  that  the  plant  cannot  be  inadvertently
switched on again and that it is indeed dead. If not observed,
there is a risk of electric shock hazard.

Ensure  protection  against  electric  shock  hazard  by  providing
adequate protection for the burner control’s connection termi-
nals.

Each  time  work  has  been  carried  out  (mounting,  installation,
service  work,  etc.),  check  to  ensure  that  wiring  and  parame-
ters is in an orderly state.

Fall  or  shock  can  adversely  affect  the  safety  functions.  Such
units must not be put into operation, even if they do not exhibit
any damage.

Introduction
The control box for the air/fuel ratio (Fig. 6), (hereafter referred to
simply as the control box), that equips the burners, carries out a se-
ries of integrated functions in order to optimise burner functioning,
both for single operation and together with other units (e.g. double
furnace boiler or more than one generator at the same time).

The basic functions carried out by the control box relate to:

flame control;

the dosage of air and fuel via the positioning (with direct servo-
control)  of  the  relative  valves,  excluding  the  possible  play  in
the mechanical cam calibration systems;

the  modulation  of  burner  output,  on  the  basis  of  the  load
requested  by  the  system,  maintaining  the  pressure  or  tem-
perature of the boiler at the working values set;

the safety diagnostic of the air and fuel circuits, via which it is
possible to easily identify any causes of malfunctioning.

Mechanical design

The following system components are integrated in the LMV37.4...
basic unit: 

Burner control with gas valve proving system 

Electronic air / fuel ratio control 

Control frequency converter air fan 

Modbus interface 

Installation notes

Always  run  high-voltage  ignition  cables  separately  while  ob-
serving the greatest possible distance to the unit and to other
cables.

Do not mix up live and neutral conductors (fire hazard, danger-
ous  failures,  loss  of  protection  against  electric  shock  hazard,
etc.).

Do  not  lay  the  connecting  cable  from  the  LMV37.4...  to  the
AZL2… together with other cables.

Electrical connection of the flame detectors

It is important to achieve practically disturbance- and loss-free sig-
nal transmission:

Never run the detector cable together with other cables.
– Line capacitance reduces the magnitude of the flame signal.
– Use a separate cable.

Observe the maximum permissible detector cable lengths.

The  ionization  probe  is  not  protected  against  electric  shock
hazard. It is mainspowered and must be protected against ac-
cidental contact.

Locate the ignition electrode and the ionization probe such that
the ignition spark cannot arc over to the ionization probe (risk
of electrical overloads).

WARNING

To avoid injury to persons, damage to property
or the environment, the following warning notes
must be observed!

The LMV37.4... is a safety device! 
Do not open, interfere with or modify the unit.

Riello  S.p.A.  will  not  assume  responsibility  for
any damage  resulting  from unauthorized inter-
ference!

WARNING

The first start-up, like every further operation for
the internal settings of the control box, requires
access by means of a password and is only to
be carried out by personnel of the Technical As-
sistance  Service  who  have  been  specifically
trained in the internal programming of the tool.

Fig. 6

D9300

Summary of Contents for RS 190/E













































Reviews: