background image

4

gENERAL

gENERAL

gENERAL SAFETY INFORMATION

 

9

Check that the product is complete, undamaged and as 

ordered as soon as you receive it. Report any discrepancies 

or damage to the 

R

 dealer who sold it.

 

9

This product must be installed by a legally qualified heating 

engineer. On completion of the installation, the installer 

must issue the owner with a declaration of conformity 

confirming  that  the  installation  has  been  completed  to 

the highest standards in compliance with the instructions 

provided by 

R

 in this instruction manual, and that it 

conforms to all applicable laws and standards.

 

9

This product must only be used for the purpose for which it 

is designed and made, as specified by 

R

R

 declines 

all responsibility, contractual or other, for damage to 

property or injury to persons or animals caused by improper 

installation, adjustment, maintenance or use.

 

9

The product must be serviced at least once a year. Servicing 

must be arranged in advance with the 

R

 Technical 

Assistance Service.

 

9

All servicing and repairs must be performed by a qualified 

heating engineer.

 

9

If water leaks from the storage cylinder, turn off the water 

supply and contact 

R

’s Technical Assistance Service or a 

qualified heating engineer immediately.

 

9

If the product is not going to be used for an extended period 

of time, contact the manufacturer’s Technical Assistance 

Service to have at least the following operations performed:

 

− Close the shut-off cocks for the domestic hot water circuit

 

− Shut down the boiler connected to the storage cylinder 

as instructed in its own manual

 

− Switch the storage cylinder OFF at the control panel (if 

fitted) and at the mains power switch

 

− Drain the central heating circuit and domestic hot water 

circuit if there is any risk of freezing.

 

9

This instruction manual is an integral part of the product. It 

must be kept safe and must ALWAYS accompany the product, 

even if it is sold to another owner or transferred to another 

user or to another installation. If you lose this manual, order 

a replacement immediately.

PRECAUTIONS

The operation of any appliance that uses electrical power 

demands that a number of fundamental safety precautions be 

respected. In particular:

 

0

Never attempt to install the system without using suitable 

personal protection equipment and without following all 

applicable occupational safety standards.

 

0

Do not touch the product when barefoot or wet if it has any 

electrical accessories installed in it.

 

0

Never  clean  or  service  the  storage  cylinder  without  first 

turning the mains power switch OFF to disconnect all 

electrical  accessories  (if  fitted)  from  the  mains  electricity 

supply.

 

0

Never pull, disconnect, or twist any electrical cables coming 

from the appliance even if it is disconnected from the mains 

electricity supply.

 

0

Do not expose the storage cylinder to the elements. It is not 

designed for use outdoors.

 

0

If the pressure in the solar collector circuit drops, do not top 

up with water alone, since this increases the risk of damage 

from freezing.

 

0

Do not use connections or safety devices or fittings (expansion 

vessels, pipes, insulation) that are not specifically designed 

and tested for use in solar water heating systems.

 

0

Do  not  allow  children  or  infirm  persons  to  operate  the 

system unsupervised.

 

0

Do not dispose of packaging material into the environment, 

or leave it within the reach of children, since it can become 

a potential hazard. Dispose of packaging material in 

compliance with applicable legislation.

general

Summary of Contents for 7200 Kombi Plus

























Reviews: