23
24
RP 218 Press Tool
RP 218 Press Tool
The RP 218 Press Tool will turn off
automatically if the battery is too low to successfully
complete a pressed connection. This will be indicated
by a continuous ON/OFF flashing of the LED light. A
fully charged battery should be inserted in the tool and
the pressed connection should be repeated as indic-
ated above.
To retract the rollers and remove the tool from the fitting if
battery dies or tool malfunctions during pressed connec-
tion. If it is necessary to retract the rollers to remove the
tool from the fitting, press the pressure release button
(Figure 1). If this happens, the connection will need to
be pressed again to insure completion.
8. After the cycle is complete, squeeze jaw arms to
open the jaws.
9. Remove the RP 218 and jaws from tube and inspect
the pressed connection. Avoid sharp edges that
may have formed on the fitting during the pressing
operation.
NOTICE
3. Check return springs in attachments with each use.
Attachments should open and close freely with only
moderate finger effort required.
Required Maintenance At RIDGID
Authorized Service Center
After 30,000 cycles, the LED light will flash three times
then pause continuously, to indicate that it is time for
maintenance and recalibration. The tool will not run if it is
not serviced within 2,000 cycles (32,000 total) after the first
flashing LED.
Maintenance service is chargeable.
Inspecting The Pressed Connection
1. Inspect the pressed fitting. If the fitting is supplied with
a control ring and/or a control label by the fitting
manufacturer, remove it. Control rings and labels
are supplied by the manufacturer to indicate that the
fitting has not yet been pressed. Removal of the con-
trol ring and label indicates to others that the con-
nection has been pressed.
Look for the following:
• Excessive misalignment of the tubes. Note that a
slight amount of misalignment at the pressed con-
nection is considered normal.
• Tubes that are not fully inserted into the fitting –
double check the insertion marks made on the
tube to see that they are still aligned with the end of
the fitting.
• Incorrect jaw or ring alignment with the fitting con-
tour, distorted or deformed fitting.
• Any other issues per the fitting manufacturer.
If any of these problems are found, then removal of
the fitting is required and a new fitting and tube will
need to be prepared and pressed in its place.
2. Test system in accordance with normal practice and
local codes.
3. See fitting system’s operator’s manual for specific
inspection criteria.
Maintenance Instructions
WARNING
Make sure battery is removed from tool before pe-
rforming maintenance or making any adjustment.
Cleaning And Lubrication
1. Wipe the tool clean daily with a clean dry cloth.
2. Inspect the attachment mounting pin and lubricate the
pin with silicone lubricant as needed.
Accessories
WARNING
The following tool accessories have been designed
to function with the RP 218 Press Tools.
Other accessories suitable for use with other tools
may create hazards when used on the RP 218.
To prevent serious injury, use only accessories
specifically designed and recommended for use
with the RP 218, such as those listed below.
Ridge Tool Company provides standard pressing
attahments designed specifically for use with
RIDGID Standard Press Tools. Only use attachments
that are specifically designed to press the fitting
system you are installing. For a complete listing
of RIDGID attachments available for this tool, see
the Ridge Tool Catalog online at www.RIDGID.cn
or call Ridge Tool Customer Services 400-820-5695.
Storage
Remove battery from tool and store tool and battery in
case. Avoid storing the tool, batteries or charger in
extreme heat or cold. The tool temperature sensor will not
allow the tool to turn on if oil temperature is not within the
temperature range of 15°F (-10°C) to 122°F (50°C). So it
may be necessary to allow the tool to warm or cool to a
temperature within the operating range by placing it in a
Description
18V 2.5 Advanced Lithium Battery Pack
18V 4.0 Advanced Lithium Battery Pack
18V Advanced Lithium Charger
China AC Power Adapter
RP 218 Press Tool Accessories
Carrying Case (Plastic)