manualshive.com logo in svg

RIDGID RD80770, Operator'S Manual

Share
Download
RIDGID RD80770 Operator'S Manual Download Page 7

7

FEATURES

Fig. 1

PRODUCT SPECIFICATIONS

Engine Size ....................................................................................................................................................................

389cc

Fuel Tank Capacity ................................................................................................................................................ 3.5 gallons
Maximum Pounds Per Square Inch Pressure* ......................................................................................................... 3,800 psi
Maximum Gallons Per Minute* ......................................................................................................................................4 gpm
Maximum Inlet Water Temperature ................................................................................................................................104˚F

*Max. rating determined by PWMA Standard 101

MOVING 

haNdle

fuel taNk

trIGGer wIth 

lOck Out

waNd 

StOraGe 

hOlSter

trIGGer 

haNdle

NOzzleS aNd 

NOzzle hOlder

Muffler 

ShIeld

hONda eNGINe

fraMe 

SuppOrt

recOIl 

Starter

chOke

fuel ValVe 

leVer

craNe 

lIftING 

hOOk

preSSure/flOw 

adjuStMeNt 

haNdle

hOSe 

StOraGe 

baG

thrOttle 

leVer

Spray waNd

Summary of Contents for RD80770



























Reviews:

No comments

Brands by name

Popular brands

Load more brands