RIDGID R884 Operator'S Manual Download Page 13

13

LED FUNCTION OF RIDGID NICKEL-CADMIUM CHARGERS

See Figure 5.

Fig. 5

POWER 

INDICATOR

EVALUATE 

INDICATOR

CHARGING 

INDICATOR

FULL 

INDICATOR

LED

INDICATOR

BATTERY 

PACK

RED

LED

GREEN

LED

ACTION

Power

Without battery pack ON

OFF

Ready to charge battery pack

Evaluate

Hot battery pack

Flashing

OFF

When battery pack reaches cooled 
temperature,  charger  begins  fast 
charge mode.

Evaluate

Cold battery pack

Flashing

OFF

When battery pack reaches warmed 
temperature,  charger  begins  fast 
charge mode.

Evaluate

Deeply discharged

Flashing

OFF

Charger  pre-charges  battery  until 
normal  voltage  is  reached,  then 
begins fast charge mode.

Defective

Defective

Flashing

Flashing

Battery pack or charger is defective

•  If defective, try to repeat the conditions a second time by removing and reinstalling the battery 

pack. If the LED status repeats a second time, try charging a different battery.

•  If a different battery charges normally, dispose of the defective pack (see 

Maintenance

 section).

•  If a different battery also indicates “Defective,” the charger may be defective.

Charging

Fast charging

ON

Flashing

See chart below for charge times

Full

Slow charging

OFF

ON

Fast charging is complete;
charger maintains charge mode

OPERATION

DEFECTIVE 

INDICATOR

GREEN LED

RED LED

BATTERY

AVERAGE CHARGE TIME

COMPACT SERIES

18 min.

HC

27 min.

HC 2.5

34 min.

Summary of Contents for R884





















Reviews: