RIDGID R855 Operator'S Manual Download Page 14

14

OPERATION

Fig. 5

EVALUATE

INDICATOR

CHARGING

INDICATOR

FULL

INDICATOR

DEFECTIVE 

INDICATOR

GREEN LED

RED LED

24v

XLi

?

Fig. 6

CHARGE LEVEL INDICATOR

See Figure 6.

The charge level indicator shows that the battery is charged 
at 1/4, 1/2, 3/4, or full capacity. To display the amount of 
charge left in the battery, press and hold the charge level 
indicator button. 

NOTE: 

When  the  battery  pack  contains  less  than  10% 

charge, the 1/4 charge level indicator will flash.

1/4 

CAPACITY

FULL

CAPACITY

CHARGE 

LEVEL  

INDICATOR 

BUTTON

CHARGE 

LEVEL INDICATOR

1/2 

CAPACITY

3/4 

CAPACITY

LED FUNCTION OF CHARGER

See Figure 5.

LED

INDICATOR

BATTERY 

PACK

RED

LED

GREEN

LED

ACTION

Charging

Fast charging

ON

OFF

Charges in 1 hour

Charging

Deeply 
Discharged

ON

OFF

Charger pre-charges battery until normal voltage 

is reached, then begins fast charge mode. May 

take longer than 1 hour to fully charge.

Full

Maintenance 
charging

OFF

ON

Fast charging is complete 
Charger maintains charge mode

Evaluate

Hot battery 
pack

Flashing OFF

When battery pack reaches cooled temperature, 
charger begins fast charge mode

Evaluate

Cold battery 
pack

Flashing OFF

When battery pack reaches warmed temperature, 

charger begins fast charge mode

Defective Defective

Flashing Flashing Battery pack or charger is defective

•  If defective, try to repeat the conditions a second time by removing and reinstalling the battery 

pack. If the LED status repeats a second time, try charging a different battery.

•  If a different battery charges normally, dispose of the defective pack (see 

Maintenance

 section).

•  If a different battery also indicates “Defective,” the charger may be defective.

Summary of Contents for R855

























Reviews: