manualshive.com logo in svg

RIDGID R4510, Operator'S Manual

Share
Download
RIDGID R4510 Operator'S Manual Download Page 16

16

ASSEMblY

TO SECURE/lEVEl THE SAW

See Figure 10.

With the leg stand open and the table saw resting on a flat, 
level surface, the saw should not move or rock from side 
to side.
If the saw rocks from side to side, the leveling feet need 
adjusting until the leg stand is balanced.

  Loosen both the top and bottom wing nuts.

  Lift the saw slightly so that you may turn the leveling foot 

until the leg stand no longer rocks.

  • Turning clockwise will lower the foot
  • Turning counterclockwise will raise the foot

TO STORE THE TAblE SAW ACCESSORIES

See Figures 11 - 12.

The table saw has two convenient storage areas (one on either 
side of the saw cabinet) specifically designed for the saw’s 
accessories.  These  accessories  must  be  securely  stored 
prior to closing the leg stand and moving the saw.

Fig. 11

blaDe 

GUaRD

RIP FeNCe

leVelING 

FOOT

WING NUT

Fig. 10

WING 

NUT

blaDe 

WReNCHeS

mITeR 

GaUGe

PUSH 

STICK

Fig. 12

aNTI-KICKbaCK 

PaWlS

aNTI-KICKbaCK 

PaWlS / blaDe GUaRD 

STORaGe

blaDe

Summary of Contents for R4510














































Reviews:

No comments

Brands by name

Popular brands

Load more brands